中文拼音 [xiāoxìngjiē]
negative integration

  • : 動詞1 (消失) disappear; vanish 2 (使消失; 消除) eliminate; dispel; remove 3 (度過; 消遣) pa...
  • : i 名詞1 (頂點; 盡頭) the utmost point; extreme 2 (地球的南北兩端; 磁體的兩端; 電源或電器上電流...
  • : Ⅰ名詞1 (性格) nature; character; disposition 2 (性能; 性質) property; quality 3 (性別) sex ...
  • : 結動詞(長出果實或種子) bear (fruit); form (seed)
  • : 合量詞(容量單位) ge, a unit of dry measure for grain (=1 decilitre)
  • 消極: 1. (否定的; 反面的) negative 2. (不求進取的; 消沉的) passive; inactive
  • 結合: 1 (發生密切聯系; 聯合) combine; unite; integrate; link; binding; coalition; cohesion; connectio...


  1. Chapter 3 bases on theory elaboration and noumenal analysis. basing on an urban viewpoint, from the dual attributes, urban attribute and the architecture individual attribute, combining the factors that affects arcade form, it analyses the characteristic of arcade form in contemporaneity conditions and the function of each essential factors. there are many factors that have an important influence on arcade form

  2. In the self - calibration scheme, the thesis emphasizes the accuracy of camera intrinsic and extrinsic parameters. we presents an accurate f method based on corresponding point adjustment. the method adjusts coresponding points according to the fixedness of projective transformed cross ratio, then calculates f matrix accurately through linear and non - linear methods. when computing intrinsic parameter, a matrix, we simplify the step, and stress on the two important parameters of a. the result will be getten through solving kruppa equation based on svd decomposition. in order to compute extrinsic parameters, we use linear method to get initial r and t, then apply non - linear method to accurate them

    提出了基於匹配點調整的f求精方法,先根據攝影交比不見對手工選擇的匹配點進行調整,再用線、非線的方法求精f矩陣;在計算內部參數a中,進行了一定的簡化,把重心放在a中重要的兩個參數上,用svd分解法計算kruppa方程;在計算外部參數時,首先用線法求解r 、 t ,然後再用非線法迭代求精。
  3. Performance for a piezoresistive transducer pressure sensor to thermal and pressure environments can be predicted by finite element method. a simplified 1 / 8 model, considering silicon dioxide and nitride process as well as stack anodic bonding and adhesive bonding processes, was developed. the fem results were found to be comparable to experimental data. case studies suggested that pyrex stack induces certain amount of non - linearity, while it isolates hard epoxy nonlinear effect. flexible epoxy bonding or soft adhesive bonding is preferred to the packaging process. the viscoelasticity and viscoplasticity of bonding material will result in hysteresis and drift errors to sensor output. however, soft adhesive s influence on sensor can be ignored under relative stable environments. more over, detailed design and process information will help to improve modeling application

    熱、壓環境下壓阻變換壓力傳感器的能可以通過有限元方法預測.這里研究了簡化的1 / 8模型,模型考慮了二氧化硅和氮化硅生成過程及堆陽和膠粘過程.果發現有限元預測果和實驗數據具有可比.範例研究表明,硼硅堆導致產生一定的非線,但它隔離了硬環氧樹脂的非線.在包裝過程中最好使用柔環氧黏或軟黏膠.黏材料的黏彈和黏塑將會導致傳感器輸出的滯后和漂移誤差.然而,在相對穩定的環境下,軟黏劑對傳感器的影響可以忽略.此外,詳細的設計和過程信息有助於提高模型的適用
  4. Professionalization of judges demands that judges as a collectivity should fulfill some basic requirements such as homogeneity, professionalization, skill, independence, neutrality and inactivity

  5. Under the careful retrospection and analysis on the previous and recent experiments about mechanical behavior of nanocrystalline metals performed by almost main investigators, the dislocation and atomic diffusion is believed to contribute hardly to the deformation of nanocrystalline alloy, and a model based on thermal activation process was applied to fit the experimental data of nanocrystalline ag

    果表明,納米晶金屬ag的不僅具有比粗晶ag高2 - 6倍的拉伸和壓縮強度,而且在大范形變階段顯示了低的加工硬化和應變速率敏感位錯理路和非晶金形變特徵,提出納米晶金屬ag的塑變形主要由於晶界滑移貢獻。