液力起步 的英文怎麼說

中文拼音 [yèlìqǐbù]
液力起步 英文
fluid start
  • 液 : 名詞（液體） liquid; fluid; juice
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 起 : 起Ⅰ動詞1 （站起; 坐起） rise; get up; stand up 2 （取出; 取走） draw out; remove; extract; pull 3...
  • 步 : Ⅰ名詞1 （步度; 腳步） pace; step 2 （階段） stage; step 3 （地步; 境地） condition; situation; st...
  • 起步 : starting; start; break the ice
  1. Ultrasonic has being attracted much attention gradually in fuel atomization because of some specialities of cavitation and infection on liquid flow. in the course of atomization of pitchy oil, especially, does it show greatly its advantage, but its material atomizational mechanism need research ulteriorly. the primary content of this thesis is about adding cantilever reed to effervescent atomizer so as to combine ultrasonic and effervescent. this thesis has discussed ultrasonic some mechanism, ultrasonic dynamical procreator, effervescent and liquid mucosity infection on atomization, at the some time we make some experiments and discuss atomization rule following some machinery parameter and run parameter so as to find some rule about ultrasonic atomization and to rich the research of ultrasonic atomization mechanism. all that will be beneficial to the design about ultrasonic atomization atomizer

    超聲波由於其空化機理及對液體的流變性影響等特性，在燃油霧化燃燒中逐步引起人們的重視，尤其在重渣油等高粘度液體的霧化過程中逐步顯示出其優越性，但其具體的霧化機理還需要做進一步的研究在氣泡霧化噴嘴基礎加入懸臂式簧片哨，將超聲波與氣泡霧化相結合是本文討論的主要內容本文從研究超聲波的一些機理入手，討論了超聲動力發生器氣泡霧化以及液體粘度對霧化質量的影響，並通過具體的實驗，根據實驗數據來討論霧化質量隨各種結構參數運行參數的變化規律，以便找到超聲霧化的一些規律，豐富對超聲霧化機理的研究，對超聲霧化噴嘴的設計具有一定的指導意義。
  2. Starting control of vehicle equipped with continuously variable transmission with torque converter is lock - up control of torque converter clutch actually. the control strategy

    雙狀態無級變速汽車的起步控制實際上是閉鎖式液力變矩器的閉鎖控制。
  3. One reason is that poor of technical level, most civil manufacturers ’ products are based on the imported electro - hydraulic proportional controller which is act as the core, as a result, the cost become higher and lost the advantage of lower cost

    在我國由於起步晚，技術水平低，汽車起重機生產廠商往往需要從國外引進電液比例控制系統核心控制器，以提升自身產品的競爭力。
  4. Nano - cuo powders were successfully prepared by pressure - hydrothermal method with cuso4 5h2o and naoh as materials. xrd, sem and tem were used to characterize the samples. the influence of raw materials " initial concentration, thermal treatment " temperature, pressure and thermal treatment " time on the morphology and size of cuo were analyzed, and the possible growth mechanism was also discussed

    以硫酸銅和氫氧化鈉為原料，用壓力-熱液法合成了納米氧化銅粉體，用xrd 、 sem 、 tem對所制得的氧化銅進行了觀察與表徵，分析了原料起始濃度、熱處理溫度、壓力、 ph值及熱處理時間對氧化銅形態和大小的影響，初步探討了不同形態氧化銅的生長機理。
分享友人
分享到 Line

分享到臉書