液壓加工法 的英文怎麼說

中文拼音 [yèyājiāgōngfǎ]
液壓加工法 英文
hydromatic process
  • 液 : 名詞（液體） liquid; fluid; juice
  • 壓 : 壓構詞成分。
  • 工 : Ⅰ名詞1 （工人和工人階級） worker; workman; the working class 2 （工作; 生產勞動） work; labour 3 ...
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 液壓 : hydraulic pressure液壓泵 hydraulic pump; 液壓表 hydraulic pressure gauge; hydraulic pressure indi...
  1. Based on the close analysis of the influence factors of the vertical bearing capacity, circular aperture extension theory is employed to establish the computing formulas for the pile vertical stress and the foundation vertical bearing capacity, respectively. moreover, with analyzing the features of the calculation parameters such as materials of gunite mortar, jet pressure, diameter of the jet pipe, pile length, pile layout, a design theory for chemical churning pile composite foundation is proposed. then, the variation of the pipe deformation with loads, the deformation coordination of pile and soil are studied

    在此基礎上深入探討了旋噴樁的樁土受力特性及其復合地基的加固機理，從影響旋噴樁復合地基豎向承載力的因素入手，基於圓孔擴張理論給出了樁體豎向應力及旋噴樁復合地基的豎向承載力計算公式;通過對噴射漿液、噴射壓力選取、噴射直徑估算、樁長及樁位設計等各種計算參數的深入分析和研究，提出了一套相應的旋噴樁復合地基設計計算方法;通過計算分析，深入探討了旋噴樁復合地基變形隨荷載變化規律、樁和樁間土變形協調關系、樁土應力比及復合地基壓縮模量的確定，並提出相應的設計方法和修正參數;此外，結合工程應用，對旋噴樁復合地基的施工技術及其現場質量檢測方法進行了較全面的探討。
  2. Especially a kind of " intelligent " automatic graphical creation of bond graph method is presented by introducing graph theory and artificial intelligence technique. this method not only improves efficiency of model input and foundation but also breaks an mformation transform path from hydraulic principle figure, bond graph model to the descriptive file

    特別是通過圖論和人工智慧技術的引入，提出了一種「智能型」鍵合圖圖形自動生成方法，在顯著加快鍵合圖模型輸入與建立效率的同時，開辟了液壓原理圖及鍵合圖模型與描述文件信息轉換的通道。
  3. According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system

    針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。
  4. Based on comparison of several technical schemes, the method of sand bedding pre - elevating and step water - filling pre - compressing is adopted. so the dissertation is consist of two parts : ( 1 ) the applicability study for the method of sand bedding pre - elevating and step water - filling pre - compressing, including numerical analyses for the thickness of sand bedding, the consolidation, settlement and stability of foundation, drainage, possibility of foundation liquefaction under seismic loading, et al. ( 2 ) monitoring at construction stage and checking the effect of foundation treatment, including the measurements of the settlement velocity and non - uniform settlement of ring beam under the tank, pore pressures and horizontal displacements in foundation, the pressure distribution at the bottom of oil tank and the strength increase of soils

    通過多種技術方案比較，最終選擇了技術先進的砂墊層預抬高分級充水預壓法，論文工作主要由以下兩部分組成： （ 1 ）砂墊層預抬高分級充水預壓法的適用性研究，其中包括砂墊層厚度、地基沉降與固結度、地基穩定性、降水、地震作用下砂土液化的可能性等方面的計算分析； （ 2 ）施工監測與地基處理效果檢驗，其中包括油罐環梁基礎沉降速率與不均勻沉降程度、各分級充水加載階段地基超靜孔壓與深層水平位移、油罐底板壓力分佈及地基土強度增長等方面的實測與數據分析。
  5. And a post - liquefaction test method has been put forward, in which the cyclic loading and the static loading courses are both controlled by stress mode. this method reflects the in - situ conditions well and truly, and a lot of tests have been done using this method. in these tests the effects of confining pressure, relative density, liquefaction severity etc. have been thoroughly investigated

    主要工作內容如下：參與研製了振動扭剪全自動多功能三軸儀，並利用其獨特試驗功能設計了一套飽水砂土液化后特性的試驗方法，試驗過程中模擬地震作用的動加載過程及模擬大變形發生的靜加載過程均採用應力控制的方式進行，試驗方法跟現場條件更為接近並用該試驗方法對相對密實度、固結壓力、液化度等對液化后變形特性的影響進行了研究。
  6. By meshing hydraulic manifold in three dimensions and considering its machining technological characteristics, a designing method to arrange the oil passages in hydraulic manifold automatically is presented in this paper

    摘要通過對液壓閥塊的三維網格劃分，結合液壓閥塊機械加工的工藝特點，本文提出了基於李氏迷宮演算法的液壓閥塊孔道自動布局的設計方法，並進行了初步的軟體實現。
  7. The physical meaning of the fuzzy neural network parameters and their influence on the model performance are discussed through the research of composite liquid - solid extrusion model, and the reasonable method of evaluating the network parameters is confirmed which can quicken the training speed. some problems and the influence of the evolution operator on the optimization course are discussed, arid the reasonable range of the evolution parameter is concluded

    通過對復合材料液-固擠壓成形工藝系統建模的研究，探討了模糊神經網路參數的物理意義及其對網路學習速度的影響，確定了可加快網路學習速度的參數賦值方法；結合液-固擠壓工藝特點探討了利用遺傳演算法進行參數優化過程中一些問題的處理方法及遺傳操作運算元對優化過程的影響，確定了參數選取的合理范圍。
  8. Power bond graph is used to established the bond graph model of the lifting and dropping of hydraulic pile hammer and state space equation in the paper for hydraulic pile hammer is perplexing nonlinear system. in order to attain the graph that pressure, position, velocity, acceleration vary with time in the course of driving pile simulation procedure solving state space equation is designed on the basis of combining four - order runge - kutta method with predicator - corrector method, dynamic simulation of the hydraulic system is studied in matlab 6. 5. it is convenient to analyse dynamic characteristics of the hydraulic syste m, beneficial to the design and parameter optimization of the hydraulic system. in the final part of the paper, under detailed analysis of the control characteristics for double - acting hydraulic pile hammer with double cylinders, control system based on the programmable logic controllers founded on technology of modern compute is designed

    由於液壓打樁錘液壓系統是一個復雜的非線性系統，本文採用功率鍵合圖法建立液壓打樁錘上行、下降的鍵合圖模型和狀態空間方程，通過四階龍格?庫塔法和預估?校正法相結合編制了模擬程序對狀態空間方程求解，在matlab6 . 5中進行液壓系統的動態模擬，獲得液壓打樁錘運動過程中壓力、位移、速度、加速度等隨時間變化的曲線圖。此曲線圖方便了對液壓系統動態特性分析，為液壓系統的設計和參數優化提供了有益的借鑒。最後，在深入分析雙缸雙作用液壓打樁錘控制系統的功能要求后，採用了以現代計算機技術為基礎的新型工業控制裝置? plc可編程式控制制器，設計出了雙缸雙作用液壓打樁錘的電器控制系統。
  9. Moreover, the data processing method of accelerated life test is used to solve the problem of the reliability data conversion under different operating status to liquid rocket engine. and the counter power law model is introduced as the relation model between the characteristic life and the combustion chamber pressure, the accelerated life equation of the constant stress accelerated life test for the weibull distribution is obtained, through the accelerated life equation, the reliability estimate of different combustion chamber pressure is calculated

    再次，採用加速壽命試驗的數據處理方法對液體火箭發動機不同工況下可靠性數據折算的問題進行了研究，引入逆冪律模型作為特徵壽命與燃燒室壓力之間的關系模型，得到了weibull分佈下恆定應力加速試驗的加速壽命方程，並通過加速壽命方程折算出不同室壓下的可靠度估計。
  10. The meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method

    本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
  11. Abstract : the meassure to reduce the static error when manufacturing axial parts on a hydralic profiling tool slide is deduced in theory with positive feedback adjusting method

    文摘:本文應用順饋校正的方法，從理論上導出了在車床上用液壓仿形刀架加工軸類零件減小穩態誤差的措施。
  12. Jet grouting is a foundation treatment method that a high - velocity grout, which is forced under high pressure out of a nozzle, cuts into the soil to form a cylindrical soil - cement solidification, and with the result of that the bearing capacity of the foundation is enhanced and the settlement and the differential settlement are reduced. this process is widely used in constructional engineering, highway bridge, coal mine and railway bed

    旋噴注漿法可在地層深處將水泥漿液等以高壓旋轉沖切土體，形成水泥土圓柱加固體，構成旋噴樁復合地基，以達到加固地基，提高承載力和減少建築物的沉降和不均勻沉降的目的，在我國建築工程、公路橋梁、煤礦和鐵路路基等建設工程中應用極為廣泛。
  13. Hot - press is a device of industrial manufacture designed to heat and press the workpieces. we designed this control system to fit the hot - press. its center unit is 89c55 single - chip microcontroller, and its output interface is a color lcd ( liquid crystal display )

    熱壓機是一種對工件加熱加壓的工業生產設備，我們設計的與熱壓機配套的控制系統，以89c55單片機為中心器件，選用了彩色液晶顯示屏作為輸出界面，實現了按工藝參數的自動運行，用改進的pid演算法對溫度和壓力實現了良好的控制，並具有快捷有效的pid參數自整定的能力。
分享友人
分享到 Line

分享到臉書