液壓驅動缸 的英文怎麼說

中文拼音 [yèyāqūdònggāng]
液壓驅動缸 英文
hydraulic drive cylinder
  • 液 : 名詞（液體） liquid; fluid; juice
  • 壓 : 壓構詞成分。
  • 驅 : 動詞1. （趕） drive （a horse, car, etc. ） 2. （快跑） run quickly 3. （趕走） expel; disperse
  • 缸 : 名詞1. （盛東西的器物） jar; jug; vat; crock 2. （缸瓦） earthenware with crude glaze 3. （像缸的器物） jar-like things
  • 液壓 : hydraulic pressure液壓泵 hydraulic pump; 液壓表 hydraulic pressure gauge; hydraulic pressure indi...
  • 驅動 : [機械工程] drive; prime mover
  1. The machine is circumgyration drilling machine that the rotary drives drilling tool to bore by rotation, adopts full hydraulic pressure drive, constant power loop, wheel cylinder startup, oil cylinder disappear ing end bumper, electrohydraulic combined control, steel wheel traveling and disassembly transport

    該機是由轉盤帶動鉆具旋轉鉆進的回轉鉆機，採用全液壓驅動，恆功率迴路，分泵啟動，油缸升降，電液復合操縱，鋼輪行走，解體運輸。
  2. The feedbacks of position, velocity, acceleration and dynamic pressure were applied to adjust the model, so the control system of single jar electrodraulic servo mechanism was built. to reduce the system error and interference error, the compound control was designed. the results of simulations showed that the magnitude attenuation and phase lag of the system come to the project demand

    引入包括位置反饋、速度反饋、加速度反饋和動壓反饋在內的反饋控制技術對電液伺服驅動機構模型進行綜合校正，從而建立單缸電液伺服控制系統，並在分析系統誤差和擾動誤差后，加入復合控制減小系統誤差和抑制干擾，模擬結果表明復合控制系統的控製品質有了明顯改善，能夠滿足工程需求。
  3. This paper introduces the working principle and controlled methods of the permanent magnet synchronization servo motor ( pmsm ), builds the mathematical model of the pmsm and analyzes the pump controlled cylinder subsystem and builds the mathematical model of it

    本文建立了永磁同步電動機的數學模型，分析了泵控缸液壓動力機構並對其建立了數學模型，進而建立了直驅式電液伺服系統數學模型。
  4. Through consulting lots of relevant references, present research of direct drive volume control hydraulic servo system is summarized in this paper, the principle and character of this system are expatiated, the principle of vector control is introduced. at the same time, the mathematical model of ac asynchronous motor is set up based on the vector control theory. the mathematical models of both the pump controlled motor and pump controlled cylinder are set up and simulated in this paper

    在查閱大量國內外相關文獻的基礎上，本文綜述了國內外對該系統研究概況，闡述了該類系統原理和特點;闡述了矢量控制的基本原理，並基於這一原理建立交流異步電動機的數學模型;分別建立了泵控馬達系統和泵控缸系統的數學模型，並給出了模擬分析;設計了用於泵控馬達系統的集成閥塊，加工了密閉壓力油罐;針對現有直驅式電液伺服裝置所存在的問題，本文主要針對系統工作過程中所產生的噪音與爬行問題進行了一定的研究。
  5. Kinematics and kinetics analysis of hydraulic cylinder powered scissors mechanism

    液壓缸驅動的剪刀撐機構運動及動力學分析
  6. The engineering drilling machine of kp2200 type is double layers bottom plate, and drives through hydraulic pressure, upper plate can move fore and aft on the lower plate, the drill power leans back under the action of oil cylinder, the lower plate can put the drilling tool within 2. 5 meters into well hole without moving, it is convenient and reliable, and ensures construction quality

    Kp2200型工程鉆機為雙層底盤，通過液壓驅動，上盤可在下盤上前後移動，鉆塔在油缸的作用下後仰，下盤不動即可把2 . 2米以內的鉆具放入井孔內，方便可靠，保證施工質量。
  7. Dynamics analysis studies the force of the actuator by the newton - euler approach, the force was created by motion parameter

    動力學運用牛頓-歐拉法進行分析，由運動平臺的運動參數得出各個液壓缸的驅動力。
分享友人
分享到 Line

分享到臉書