液態乾燥劑 的英文怎麼說
中文拼音 [yètàigānzàojì]
液態乾燥劑
英文
liquid desiccant- 液 : 名詞（液體） liquid; fluid; juice
- 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
- 乾 : Ⅰ名詞1. （八卦之一） qian, one of the eight diagrams2. （姓氏） a surname Ⅱ形容詞（舊時稱男性的） male
- 燥 : Ⅰ形容詞（缺少水分） dry Ⅱ名詞[中醫] （病因） dryness
- 劑 : Ⅰ名詞1 （藥劑; 制劑） a pharmaceutical or other chemical preparation 2 （某些有化學作用的物品） a...
- 液態 : [物理學] liquid state液態空氣 liquid air; 液態氣體 liquid gas
- 乾燥 : arefaction
-
A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well
液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。The analytic results of the effects on the micromorphological structure of the film by the electrochemical condition ' s showed that the carbon is apt to improve the boundary combination between the scfs and the surface of the cathode and the seperation of the films, and that the micromorphological structure of the mpgcfs is greatly affected by the dring and the power voltage, which remarkably affluence ion move in swelling cathode film, and that higher temperature and concentration of cu2 + in the medium solution are also advanagable to the deposition of cu in scfs. the plot of deformation behavior of mpgcfs showed that the maximum strench ratio decreases and the brittleness increases due to the existence of the metal phase, and that the strengh trend of the composite films is fistly up and down followed with the content of metal phase because of the change of the role of the metal phase from acting as the physical cross - linking to weakening the films due to destroying the whole structure of the polymer
另外它作為基體的另一個突出的優點是制備的溶脹復合膜（ scf ）中的溶劑與電解液中的溶劑相同都是水，克服了以前膜內外不同溶劑之間擴散的問題，結果使得電流最終趨於一種穩態，因此可以更好實現用電化學條件來控制mpgcf的形態結構；硬質石墨材料的多孔的結構和石墨本身的結構性能特點使得碳作為陰極材料時有利於溶漲復合膜（ scf ）與電極表面的結合以及膜的剝離，因此是作為陰極的理想材料；電化學條件中的乾燥程度和電壓能夠明顯的影響離子在膜內的遷移，從而對mpgcf的形態結構造成較大的影響；而提高反應溫度和增大電解液中銅離子的濃度也有利於銅在膜中的沉積生長。
分享友人