液體細霧 的英文怎麼說

中文拼音 [yètǐxìwù]
液體細霧 英文
fine spray of liquid eg from an aerosol
  • 液 : 名詞（液體） liquid; fluid; juice
  • 體 : 體構詞成分。
  • 細 : 形容詞1 （條狀物橫剖面小） thin; slender 2 （顆粒小） in small particles; fine 3 （音量小） thin ...
  • 霧 : 名詞1. （水蒸氣凝結成的小水點） fog 2. （像霧的許多小水點） fine spray
  • 液體 : liquid; liquor; fluid
  1. Spraying the liquid turns it into many fine droplets.

    噴射液體，使它變成許多細小的霧沫。
  2. The cold fog is produced by a special device ( cold fogger ) that breaks up the chemical into microscopic droplets by mechanical means, basically with a high - pressure pump and an extreme fine nozzle

    （冷噴霧器）製造。基本來說，此裝置用高壓泵和極細的噴嘴，以機械方法把化學液體變成微細的霧滴。
  3. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  4. The fog is produced by a device ( thermal fogger ) that uses heat to break up the chemical into very small droplets ( usually in 5 - 30 micron diameter range ) which will disperse in the air

    熱噴霧是經由一特製裝置（熱噴霧器） ，利用熱力把化學液體化為微細霧滴（直徑通常由5至30微米不等）散播並懸浮於空氣中。
分享友人
分享到 Line

分享到臉書