液體負壓計 的英文怎麼說

中文拼音 [yètǐfùyājì]
液體負壓計 英文
liquid gage
  • 液 : 名詞（液體） liquid; fluid; juice
  • 體 : 體構詞成分。
  • 負 : Ⅰ名詞1 （負擔） burden; load 2 （虧損） loss 3 （失敗） defeat Ⅱ動詞1 [書面語] （背） carry on th...
  • 壓 : 壓構詞成分。
  • 計 : Ⅰ動詞1 （計算） count; compute; calculate; number 2 （設想; 打算） plan; plot Ⅱ名詞1 （測量或計算...
  • 液體 : liquid; liquor; fluid
  • 負壓 : [物理學] negative pressure; subatmospheric pressure
  1. A lot of experiments have been done in the process of exploiture soft packaging li - ion battery about how to choice the rational arts and crafts. the content include : how to deal with the collector, add how much pvdf in the material, how long the material need to stirring and the right viscidity, how much condubtivity agent the electrode need, what theckness is best, choice different collectors, the degree of dryness of the electrode, theckness of pressed model, how much electrolyte will be added, placement how long after added the electrolyte, system of formation how to influnce the battery, in formation the battery need or not need preesure from outside, how to vacuumize and the optimize matching positive pole and negative pole. with these practice make sure the parameter of the positive pole should less than 90 m ; according to different vacuumize order the conduc - tivity agent in anode will be 5mass % and 9mass %, respectively, and in cathode the data is 2mass % ; every 100mah added to 0. 4 ml electrolyte ; before formation the battery should be placement 8 hours and the system of formation must be less than 0. 01c before the voltage reach to 3. 0v ; should press in outside when battery in formation ; to these batteries which capacity more than 350mah the vacuum time not excess 15s ; the optimize matching positive pole and negative pole between 2. 10 : 1 and 2. 15 : 1. finally make out the battery which cycling performance and security are all very well

    液態軟包裝鋰離子電池的研究主要是對關鍵工藝進行了優化設計，具體包括:集流體的處理、 pvdf的加入量、漿料攪拌時間和粘度、導電劑的加入量、電極膜的厚度、不同集流體的選擇、電極膜的乾燥程度、壓型的厚度、電解液的加入量、注入電解液后靜置時間的長短、化成制度的影響、化成時電池所具有的壓力影響、抽真空的處理、正負極活性物質的匹配。最後確定出液態軟包裝鋰離子電池最佳工藝參數:正極膜的厚度小於90 m ;根據化成時不同抽真空順序，確定正極膜中的導電劑的加入量分別為5mass %和9mass % ;負極膜中導電劑的加入量為2mass % ;電解液的加入量為每100mah添加0 . 4ml ;化成前電池的靜置時間應當大於8h ;電池在3 . 0v之前採用小於0 . 01c的化成制度;在化成過程中應當施加一定的外部壓力;對於350mah的電池抽真空的延時不應大於15s ;而正負極活性物質的質量比應當在2 . 1 : 1 2 . 15 : 1之間。
  2. A simple pressure - reduced capillary viscometer was designed. it was used for studying the abnormal rheological properties of surfactant solutions, such as fluid patterns, thixotropy and negative thixotropy

    安裝了一種簡單的減壓型毛細管粘度計，用於測量非牛頓性表面活性劑溶液的流變性質，如判斷流體類型，判斷流體的觸變性及負觸變性等。
  3. That is, through analysis of the principle on flow control and " hydraulic transistor ", design and calculation of flow control characteristic as well as main parts in valve inner chamber, a piloted reducing valve will be installed between main valve and pilot valve. after a pressure - difference compensating reducing valve was added in the non - pressure compensating piloted reducing valve of the flow control valve in vlalvistor valve, the calculation on control characteristic emulation and load characteristic emulation has been carried out. the result of the calculation shows that after pressure compensating reducing valve was added, the linearity of the control characteristics has been greatly improved thus eliminating influence upon outlet flow by load pressure - change of the hydraulic system and improving performance characteristics of the hydraulic component

    文章還在對瑞典valvistor閥的插裝比例閥研究的基礎上，提出了一種新的流量控制原理，即：通過對流量控制和「液壓晶體管」原理的分析、流量控制特性及閥內腔主要結構件的設計計算，在主閥和導閥之間增設先導減壓閥，並進一步對valvistor閥的流量控制閥之無壓力補償先導減壓閥、加入壓差補償減壓閥后的控制特性進行了模擬計算和負載特性模擬計算，結果表明：增設壓力補償先導增壓閥后，其控制特性曲線變得非常線性，從而消除了液壓系統負載壓力變化對主閥輸出流量的影響。
  4. In the last part of the chapter, the research method of the overall thesis is proposed. in chapter 2, the overall design scheme of electro - hydraulic proportional control system of material testing machine is introduced

    第二章介紹了材料試驗機負載適應控制系統的總體設計方案，詳細介紹了本課題研究開發的主機系統、液壓控制系統及電控系統。
分享友人
分享到 Line

分享到臉書