淬火加熱 的英文怎麼說

中文拼音 [cuìhuǒjiārè]
淬火加熱 英文
hardening heat
  • 淬 : 動詞（淬火） temper by dipping in water, oil, etc. ; quench
  • 火 : fire
  1. In our company we have forging, costing and heat treatment workshops with advanced producing equipments. all the tasks which refused by the other companies will be done well here. there are many large - size air hammers, blast furnaces and costing equipment including all sorts of heats treatment equipment, costing equipment including all sorts of heat treatment equipments

    我公司下屬鍛造鑄造熱處理加工廠各一座，有先進的生產設備，可以接收其它部門不願承攬，甚至不敢承攬的艱巨任務，我們有大型的空氣錘和高爐冶煉鑄造設施和場地，有淬火退火回火各種熱處理設備。
  2. Medium frequency induction heating equipment are used in metal melting, temperature keeping, diathermic technology, metal - heat processing brass soldering, quenching, tempering and sintering

    中頻感應加熱設備適用於各種金屬熔煉，保溫，透熱，金屬熱處理，釬焊，淬火回火，燒結，釬絲鋼絲等。
  3. Induction heated oil tempered spring wire is a kind of new technical material which has been developed since 1980s. it can be heated by means of eddy induced into itself through electromagnetic coil and this method is mainly used in surface quenching. with correct designing and reasonable current frequency, induction coil and heat treatment process selected, as well as plc controlling applied, the wire can be uniform heated along cross - sectional and longitudinal direction and can be quenched and tempered continuously

    應加熱油淬火-回火彈簧鋼絲，是二十世紀八十年代發展起來的新技術材料，在國外稱為itw induction heat oil tempered spring wire 。是通過線圈電磁感應鋼絲本身產生的渦流進行加熱，通常主要用於表面淬火。經正確設計，選擇電流頻率，合理的感應線圈及熱處理工藝，並實施plc控制，可使鋼絲整個截面及長度上得到均勻加熱，進行連續整體淬火和回火。
  4. Process features characteristic of induction heat oil tempered spring wire

    感應加熱油淬火-回火線材特點
  5. Our company dominating products cover : 1. high - frequency heating equipment ; 2. high - frequency medium heating equipment ; 3. whole - solid high and moderate frequency power ; 4. quenching machine tool and moderate frequency power

    本公司主要產品為： 1 、高頻感應加熱設備、 2 、高頻介質加熱設備、 3 、全固態高中頻電源、 4 、淬火機床及中頻電源。
  6. Mathematical model for temperature distribution calculation during wheel quench heating process is established and used in the simulation of a certain type wheel

    摘要根據馬鋼車輪淬火加熱爐的實際狀況，建立了車輪淬火加熱過程溫度場計算模型。
  7. Improvement for spray quenching process of grooved roll with integrally differential heating

    開槽軋輥整體差溫加熱噴霧淬火工藝的改進
  8. Methods of measuring case depth for steel hardened by flame or induction hardening process

    鋼的火焰加熱淬火或感應加熱淬火硬化層深度的測量方法
  9. Today, salt - bath stove is still one of the main heating equipments in the heat - treating workshops

    鹽浴爐是熱處理車間的主要加熱設備之一，多用於零件的淬火、回火、正火等處理。
  10. Comparison of two heating methods of isothermal quenching used for adi friction wedges

    斜楔的兩種等溫淬火加熱工藝的比較
  11. Moreover, a method for iterating thermal and magnetic analysis is put forward. in chapter 5, the distributed characteristics of eddy and temperature fields in induction heating process are simulation by fem respectively, including the distributions of eddy and temperature fields during the whole induction heating process, the influence of frequency and magnetic disperse, and the prediction of hardened depth

    第五章:用ansys軟體對感應加熱過程中工件內渦流場、溫度場的一些基本問題進行模擬及分析，主要包括:加熱過程中工件渦流功率密度及溫度分佈規律;頻率與磁力線逸散對加熱效果的影響;同時對感應淬火淬硬層深度進行了模擬預測。
  12. Results of the experiments showed that the wear mechanisms of the sintered steel included abrasive wear, adhesive wear and fatigue wear, and it was the abrasive wear most important. it was the sintered steel mixed by ni, mo that was the best on the wear resistance, because of the great lot of bainite ; the sintered steel quenched and low temperature tempered mixed by mo, w that was the best on the wear resistance, because of the rigidity of the steel was the highest

    實驗結果表明：本文中幾種燒結鋼的磨損機制均是由磨粒磨損、粘著磨損、和疲勞磨損共同作用的，且以磨粒磨損為主；在燒結態下，復合添加合金元素鎳、鉬的燒結鋼的耐磨性能最好，這是因為生成了大量的硬質相貝氏體；而淬火、低溫回火態下，則復合添加鉬、鎢的燒結鋼的耐磨性能最好，這是因為熱處理態下添加鉬、鎢的燒結鋼的硬度最高。
  13. The difference among the elasticity modulus of various microstructures is probably the main reason, which caused the experiment results above. under the same experiment conditions, such as sample shape, size, surface roughness, establishment of testing system, pressure on the probe, and thickness of coupling medium, the variety of relative attenuation coefficient ( or ) in different heat treatment samples is measured and compared by measuring the attenuation obtained from the cylindrical surface of column. the result is as following : for 40cr and 38crmoal, a mt < az mq < a s < a p + f ; for gcrlssimn, a mt < a annea < s < a p + f ; and a increased with the increasing of frequency

    在保證試樣形狀、尺寸、表面光潔度、系統參數設置、施加在探頭上的壓力以及耦合層厚度等測試條件一致的情況下，利用棒材圓柱面測衰減系數法，分別測定並比較上述不同熱處理試樣相對衰減系數的變化情況，得到的實驗結果是：對於40cr及38crmoal鋼， _ （低溫回火） （淬火） _ （高溫回火） _ （正火） ；對于gcr15simn鋼， _ （低溫回火） _ （退火） _ （高溫回火） _ （正火） ；且隨著頻率的提高，衰減系數均呈現增加的趨勢。
  14. The company is specialized in producing of mesh - belt continuous sintering furnace 、 pusher - type high temperature sintering furnace 、 steel - belt iron powder refining reduction furnace （ electric - heating rbo furnace and direct gas - burning heating rbo furnace are also produced ） 、 pressure bell type furnace 、 carburizing quench furnace and some kinds of accessorial equipments

    目前生產項目有：網帶式連續燒結爐、推桿式高溫燒結爐、蒸汽處理爐、鋼帶式鐵粉還原爐（電加熱、氣體燃燒直接加熱rbo型均生產） 、加壓鐘罩爐、滲碳淬火爐及各種輔助設備。
  15. In chapter four, in our experiments, we selected four representative mould steels as samples. after laser heat treatment, the hardness of samples was measured by special instrument, microstructure was also photographed to be analyzed carefully. through these experiments, we also debated on the theories which explain the new phenomenon occurring in laser overlapping treatment

    第二章：介紹了工業中的各種激光加工技術和激光加工系統，詳細說明了本實驗所使用的高功率激光加工系統；第三章：詳細敘述了激光淬火的機理和熱傳導數學模型；第四章：通過實驗，分析激光淬火后的模具鋼的硬化帶的硬度分佈及金相組織特性，同時對激光交疊熱處理的特點及形成機理都作了深入的探討。
  16. Laser quenching is one of the important field of using laser technology in industry, which is closely connected with several subjects, i. e. laser physics theory, laser processing technology, metal physics et, al

    激光淬火（相變硬化）是激光技術在工業中應用的一個重要領域，該技術與激光物理學、激光加工技術、金屬學熱處理等幾門學科緊密相關。
  17. The company deals with the heat treatment processing of various specification, type and kind of ferrous nonferrous metal, including anneal, quenching, hardening tempering, carburizing, solid solution, aging, vacuum heat treatment, high frequency treatment, blueing, nitriding and ion nitriding etc, the annual capacity of which is more than 18, 000t

    我公司可以承攬各種規格型號品種的黑色金屬有色金屬熱處理加工業務，包括：退火正火回火淬火調質滲碳固溶時效真空熱處理高頻處理發藍氮化離子氮化等。年加工能力22000餘噸，年加工產量出口佔70 % 。
  18. Sino - foreign joint venture nanjing dongwu metal material co., ltd. is a hi - tech enterprise which specially produces and sells induction heat oil tempered spring wire and die pusher rod

    中外合資南京東吳金屬製品有限公司是一家專門生產經營感應加熱油淬火-回火彈簧鋼絲冷鐓鋼絲軸承鋼絲異形鋼絲退火磨光定尺線材冷拉鋼絲和模具推桿線材的高新技術企業。
  19. Un - thoroughly heating and spraying quenching process for large size monoblock backup roll

    大型整鍛支承輥不透燒加熱噴霧淬火工藝實踐
  20. The effect of plastic deformation and elastic strain energy induced by pre - strain on the nucleation of martensitic transformation of low alloy ultra - strength steel sosimncrmov had been studied by pre - strain quenching in austenite state. the control over deformation magnitude and deformation temperate as well as loading pattern was performed to adjust the storage of elastic strain energy in steel before martensitic transformation, using the type of geeble - 1500 thermal analogue test machine

    使用gleeble - 1500型熱模擬機，對低合金超高強度鋼30simncrmov實施奧氏體預應變淬火處理，通過控制形變量、形變溫度和加載方式，調整鋼中馬氏體相變前的彈性應變能儲備，研究了預應變所造成的塑性變形與彈性應變能對馬氏體相變的影響。
分享友人
分享到 Line

分享到臉書