淬火速率 的英文怎麼說
中文拼音 [cuìhuǒsùlǜ]
淬火速率
英文
quenching rate-
The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed
研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。According to structural characteristics of multi - phased alloy steels and the properties of ultrasonic propagation, microstructures characterization with different heat treatment processes ( normalizing, quenching / annealing, quenching plus low tempering, quenching plus high tempering ) for three steels ( 40cr, 38crmoal, gcrlssimn ) was studied experimentally by using ultrasonic methods. ultrasonic velocity, relative attenuation coefficient, and power spectral analyses were researched on the same samples respectively, on the basis of theory and experiment, the sensitivity and other characterizations of the three methods used to distinguish different microstructures were compared
根據具有多種相結構合金鋼不同熱處理轉變產物的組織特點，以及超聲波在其中的傳播規律，利用超聲波速度、相對衰減系數以及功率譜分析三種方法，對三種鋼（ 40cr 、 38crmoal及gcr15simn ）不同熱處理（正火、淬火退火、淬火+低溫回火及淬火+高溫回火）轉變產物的顯微組織進行了超聲表徵研究。From an examination of the tensile behavior of cz ly12 alloys under different temperature and strain rate, two kinds of deformation and intergranular fracture behaviors were observed that were opposite to the characteristic strain rate range in fine - grained superplasticity. the mechanisms are described as follows. the high ductility achieved at high strain rate is generally attributed to the dominant role of gbs accommodating mechanisms, which is considered as dislocation creep within grains controlled by subgrains
研究選用自然時效淬火態的ly12鋁合金，進行了一系列不同溫度和應變速率下的單軸拉伸試驗， 480下，觀察到與傳統細晶超塑性特徵區間相反的行為：較高應變速率下，動態再結晶使晶粒細化，促進了晶界滑移，亞晶界控制的晶內位錯蠕變是晶界滑移的主要協調機制。For example, the quenching and quenching plus low tempered structure of 38crmoal are hard to be differentiated by velocity method and the principal frequency technique. it will be better if they are differentiated by the method of relative attenuation coefficient
38crmoal鋼的淬火與淬火+低溫回火組織，用聲速法和主頻率比較法都難以區分，最好的方法是比較功率譜譜峰特徵（幅度、數量、分佈） 。A high speed quench cooling manipulator can be added to the stage so that cooling rates of > 5000 c / min can be achieved ( faster than immersing in ln2 )
此臺體具有高速淬火冷卻功能，冷卻速率大於5000 c /分（比浸入液旦還快） 。分享友人