淬硬表面 的英文怎麼說

中文拼音 [cuìyìngbiǎomiàn]
淬硬表面 英文
hardened face
  • : 動詞(淬火) temper by dipping in water, oil, etc. ; quench
  • : 形容詞1 (堅硬) hard; stiff; tough 2 (剛強; 堅定; 強硬) strong; firm; tough; obstinate 3 (勉...
  • : Ⅰ名詞1 (外面;外表) outside; surface; external 2 (中表親戚) the relationship between the child...
  • : Ⅰ名詞1 (頭的前部; 臉) face 2 (物體的表面) surface; top 3 (外露的一層或正面) outside; the ri...
  • 表面 : surface; superficies; boundary; face; rind; sheet; skin; outside; appearance
  1. Abstract : in this paper, the surface of the ore milling roller was quenchedby the laser, so that increase its surface rigidity and improve its antiwear properties, and prolong its life

    文摘:應用激光束對磨輥進行火處理,提高磨輥度,增強磨輥的抗磨損性能,從而達到延壽的目的。
  2. Steel products. determination of the effective depth of hardening after flame or induction hardening

    鋼產品.或感應火后化有效深度的測定
  3. Austemper case hardening

    等溫
  4. Iron and steel - determination of the conventional depth of hardening after surface heating ; german version en 10328 : 2005

    鋼鐵.加熱后常規深度的測定
  5. Abstract : this paper discussed the physicalmetallurgical process during laser hardening withsteel and cast iron, presented the technique designprinciple of laser hardening to achieve good resultsit also introduced the inspection method for laserhardened surface of steel and cast iron

    文摘:討論了鋼和鑄鐵在激光時的物理冶金學過程,提出了激光獲得優良效果的工藝設計依據,介紹了對鋼鐵零件激光層的檢驗方法。
  6. Meanwhile, the fracture was accelerated due to the uneven surface hardness and the unreasonable distribution of the hardening layer on the crankshaft, and the bad lubrication condition in service

    同時軸左頸度不均勻、層分佈不甚合理,工作過程中潤滑條件差,加速了曲軸的斷裂。
  7. Considering different microstructures and properties of metal of hardened layer and the core of back - up roller, the distributions of shear stress below surface and the contact stress between work roller and back - up roller of a four - high - mill were simulated with nonlinear fem

    摘要考慮軋輥層與其心部金屬材料組織性能的差別,採用非線性有限元方法對四輥軋機的工作輥與支撐輥間接觸應力及輥內剪應力分佈進行模擬,並將模擬結果與傳統強度校核方法進行了對比分析,研究了軋輥層厚度對輥間接觸應力的影響規律。
  8. I. investigation on laser surface hardening for metal materials in this work, the effect of the process parameters in laser surface hardening on the properties and surface feature of the hardened layer was studied

    一、金屬材料激光化技術研究。研究了激光火工藝參數和化層性能、強化效果之間的關系,對大積激光火技術的基礎理論及搭接方法對組織性能的影響規律進行了探討。
  9. Ferrous metals, non - ferrous metals, ic thin sections, coatings, ply - metals ; glass, ceramics, agate, precious stones ; hardness testing such as that on the depth and the trapezium of the carbonized layers and quench hardened layers

    黑色金屬、有色金屬、 ic薄片、層壓金屬、塗層;玻璃、陶瓷、瑪瑙、寶石等;炭化層和化層的深度及梯度的度測試。
  10. The vc - fe surface composite shows high wear - resistance, it ' s wear - resistance is 4. 20 times as that of chilling respectively. with the content of v increasing, it ' s rigidity and wear - resistance increases continually. more vc grains gained, and well distributed, better wear - resistance the vc - fe surface composite will show. ( 7 ) surface cermet composite was formed by the means of cast - sintering technique, with the help of adding wc grains and the quantity of heat sent out from the reaction v + c vc, the carbide cermet quality percent exceeds 60 %

    在重載干滑動摩擦條件下, vc一fe復合材料顯示了很高的耐磨性,其相對耐磨性是可鑄鐵的4 . 2倍:隨著含v量的增加, vc一fe復合材料的鑄態度和耐磨性不斷提高, vc顆粒越多,分佈越均勻,復合材料的耐磨性就愈好。
  11. The reasons why surface of workpiece is moistened from bottom to top in quenching and axial hardness gradient is generated after quenching are also given in this paper

    對試驗中所觀察到的工件由底部向頂部逐漸潤濕的現象,以及火后工件產生軸向度梯度的原因進行了解釋。
分享友人