混合溶液法 的英文怎麼說

中文拼音 [húngěróngyèfǎ]
混合溶液法 英文
mixed solution method
  • 混 : 混形容詞1. （渾濁） muddy; turbid2. （糊塗; 不明事理） foolish; stupid
  • 合 : 合量詞（容量單位） ge, a unit of dry measure for grain （=1 decilitre）
  • 溶 : 動詞（溶化; 溶解） dissolve
  • 液 : 名詞（液體） liquid; fluid; juice
  • 法 : Ⅰ名詞1 （由國家制定或認可的行為規則的總稱） law 2 （方法; 方式） way; method; mode; means 3 （標...
  • 混合 : （攙雜在一起） mix; blend; mingle; admix; mixture; mix up; interfusion; commixture; blending; cre...
  • 溶液 : solution; liquor; scald; aqua
  1. The disperse degree of the ceramic can greatly affect uniformity of the composite, which limit the poling voltage and affect the piezoelectricity. in this paper, the relationships among constitutes, microstructures, dielectric and piezoelectric properties were calculated by employing the banno unit cell mode ; pzt ceramic were synthesized by the hydrothermal method and the appropriate solution was selected according the adsorption of pvdf on the ceramic particle surface ; then, relationships between the disperse degree and the fabrication process were studied. base on these, the pzt / pvdf composites intermingled some pan were prepared and the microstructures were investigated

    論文首先利用bannounitcell模型，計算了pzt pvdf壓電復合材料的組成、結構、與其壓電和介電等性能之間的關系；針對壓電復合材料存在的均勻分散性差的缺點，選用水熱法制備的粒度均勻的pzt陶瓷粉末，並採用溶液混和法與聚合物pvdf進行分散復合，重點研究了不同工藝條件下陶瓷的均勻分散性及其與材料微觀結構之間的關系。
  2. Theoretical analysis and experimental results show that the mentioned methods above can simplify the process condition, improve the etched effect, shorten the etching time and obtain more even etched surface. 2 ) laser - assisted wet sequencially - selective - etching method has been developed this method can be applied when the corrosion solution is mixed solvent

    2 ）提出了激光化學誘導液相次序選擇腐蝕法該方法適用於腐蝕液為混合溶劑的情況，例如， h2so4 - h2o2對gaas基片進行腐蝕時，先採用h2o2對基片進行氧化腐蝕處理，再利用h2so4進行激光化學腐蝕。
  3. On the other hand, through inhibted performances of concrete and mortar, the permeability refutations with different w / c, ages, admixture, and physics chemistry absorb regulation of different viscosity permeable liquid, the liquid - gas method is proved science and accuracy. because adopting with liquid - gas method it case clearer concrete permeability regulation. different concretes relativity is more exact and more efficiency and fixed quantity

    另一方面，我們利用混凝土所固有的性質：不同水灰比混凝土、砂漿、抗滲性能規律；不同齡期混凝土的抗滲規律；不同外加劑、摻合料抗滲性能之間相互對比規律；不同黏度滲透液物理化學吸附對測試結果影響的規律；用規律來映證溶液氣壓法的科學性，準確性。
  4. In order to prepare bioactive functional fibers, the german company zimmer blended seaweed particles with the spinning solution during the solvent spun process for cellulose fibers, and dispersed the seaweed particles in the resultant seacell fibers

    摘要為了制備具有生物活性的功能性纖維，在溶劑法生產再生纖維素纖維的過程中，把海藻粉末與紡絲溶液混合，所得到的海絲纖維中分佈了細小的海藻顆粒。
  5. The investigation presents a new method of dipping sic kiln furniture into 2 saturable solution or into the saturable solution of ca3 ( po4 ) 2 and a1po4 in order to beneficial to its crystalline structure change and its properties, to make it packed and decrease its porosity. it can also hinder the diffusion of oxygen so as to decrease the oxidation rate and lengthen the useful life. the mechanism of dipping two kinds of phosphate saturable solution were studied and proved by the results of scanning electron microscope

    本研究首次採用sic窯具材料浸漬ca _ 3 （ po _ 4 ） _ 2飽和溶液和浸漬ca _ 3 （ po _ 4 ） _ 2與alpo _ 4混合飽和溶液的方法，目的在於有利於窯具材料晶相結構的轉化和性能的優化；能堵塞材料的氣孔，降低透氣率，阻礙o _ 2擴散，降低氧化速度，延長窯具材料的使用壽命。
  6. Cadmium ( cd ) is one of the mostly polluting heavy metal. first, to characterize the adsorption property of cadmium, cadmium adsorption isotherms in soils were determined by the batch experiment, and the adsorption parameters were obtained ; second, miscible displacement experiments were carried out in saturated homogeneous soil columns under steady - state water flow, and the dynamics of flux concentration of cadmium leached in soils were measured

    首先，用批量平衡法開展了鎘在砂質壤土、壤質砂土和粉壤土中的吸附特性的試驗研究，獲得吸附常數；其次，採用易混合置換實驗的方法，對其在穩定流場飽和土壤中的運移進行了室內研究，獲得了目標溶質鎘在定濃度輸入條件下的出流液濃度動態。
  7. The preparing process is as follow : mixing the nickel salt, zirconium salt and stabilizer in the solvent ( distilled water ) to prepare mixing solution according to a certain ratio ; commingling the mixing solution and coordination solution of carboxylic ammonia in accordance with a certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powders and the zro2 - ni nanocrystalline composite powders were gained by reducing the zro2 - nio powders

    方法如下：將鎳鹽、鋯鹽、穩定劑和水溶劑按所需成分配成混和溶液，再將混和溶液、外加劑按比例混和形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到ysz - nio氧化物納米粉末，將該氧化物粉術還原得到ysz - ni納米復合粉術。絡合。
  8. In this study, the preparing processes of zro2 - ni nanocrystalline composite powder aremixing the nickel salt, zirconium salt and stabilizer, solvent ( distilled water ) together to prepare the mixing solution according to certain ratio ; commingling the mixing solution, coordination solution of carboxylic ammonia, intrusion aid in accordance with certain rate to form sol, drying the sol and turning it into gel, pre - sintering the gel to get the zro2 - nio powder and gaining zro2 - ni nanocrystalline composite powder by reducing the zro2 - nio powder. xrd, x - ray wide - angle diffractometer, bet, sem, tem, hrtem analyses are used to study the zro2 - ni nanocrystalline composite powder and zro2 - ni cermet. the sintering temperature is determined

    本研究的zro _ 2 - ni納米復合粉末的制備方法如下：將鎳鹽、鋯鹽、穩定劑和溶劑（水）按所需成分配成混合溶液，再將混合溶液、外加劑和氨羧絡合劑按比例混合形成溶膠，溶膠經乾燥成為凝膠，凝膠經預燒得到zro _ 2 - nio納米粉，將該氧化物粉還原得到zro _ 2 - ni納米復合粉。
  9. A research on raman spectroscopy of mixed liquor of ch3oh and c2h5oh

    乙醇和甲醇混合溶液的拉曼光譜法研究
  10. Glass - resistance to attack by boiling aqueous solution of mixed alkali - method of test and classification

    玻璃耐沸騰混合堿水溶液浸蝕性的試驗方法和分級
  11. Glass - resistance to attack by a boiling aqueous solution of mixed alkali - method of test and classification

    玻璃耐沸騰混合堿水溶液浸蝕性的試驗方法和分級
  12. Glass. resistance to attack by a boiling aqueous solution of mixed alkali. method of test and classification

    玻璃.耐沸騰混合堿水溶液侵蝕.試驗方法和分類
  13. By using the method of orthogonal table, the water binder ratio, air content and mineral admixtures which affect the saturation degree are analyzed in this paper. meanwhile in freezing and thawing cycle circumstance including water environment and 3. 5 % nacl liquor, the saturation degree and the saturation rate are also analyzed. moisture content of the concrete is different by varying water pressure

    本文採用正交分析方法，研究了自然飽水和壓力飽水條件下水膠比、含氣量和摻合料三個因素對混凝土飽和系數的影響規律，並研究了混凝土在純水和3 . 5 % nacl溶液中受凍后飽和系數的變化規律。
  14. Chemical resistance of glass used in the production of laboratory glassware - method for determination of resistance of glass to attack by a boiling aqueous solution of mixed alkali

    製作實驗室玻璃器皿用玻璃的耐化學腐蝕性.第1部分:玻璃耐混合強堿沸水溶液腐蝕測定方法
  15. In attempt to prepare and study the novel electrically conductive nanocomposites, with polyethylene ( pe ) served as the matrix, maleic anhydride grafted polyethylene ( gpe ) served as eg intercalates and expanded graphite ( eg ) served as a conductive filler, prepared gpe / eg, pe / gpe / eg electrically conductive composites via solution intercalation ( si ), direct melt mixing ( dmm ) and master batch melt mixing ( mmm ) methods. by means of testing conductivity and mechanical property, with the measures of tem, sem, om, xrd and dsc, studied the relationship between preparation method, material composition, and electrically conductive as well as mechanical property. the main outcomes never reported at home and abroad literature were obtained as follows : 1 the gpe / eg electrically conductive nanocomposites were prepared via si method

    本論文以制備和研究新型高分子導電納米復合材料為目的，以聚乙烯（ pe ）為基體，馬來酸酐接枝聚乙烯（ gpe ）為插層劑，膨脹石墨（ eg ）為導電填料，採用溶液插層（ si ）法、直接熔體混合（ dmm ）法和兩者相結合的熔體母料混合（ mmm ）法制備了gpe eg 、 pe gpe eg導電復合材料，通過電導率和力學性能測試，運用tem 、 sem 、 om 、 xrd和dsc等手段，研究了制備方法、材料組成、形態結構和導電性能及力學性能之間的關系，得到以下未見國內外文獻報道的研究結果： 1採用si法成功制備了gpe eg導電納米復合材料，其導電逾滲閥值（ _ c ）為1 . 59vol ，遠低於dmm法制得gpe eg常規復合材料的_ c （ 3 . 13vol ） 。
  16. Carbon nanotubes were separately synthesized by a new pulsed laser ablation ( pla ) for in - situ growth method and cvd support method in this paper. ft - ir, uv - vis, xfs, laman, tem, xrd, bet methods were used to characterize the sol, carbon nanotube and other products in the experiment. in the pla method, the sols containing carbon nanotubes were successively obtained by using 1064nm pulsed laser to ablate the interface of fe / c, or ni / c targets and ethanol under common temperature and pressure, and then carbon nanotubes were directly acquired by evaporating the ethanol

    脈沖激光轟擊原位生長法是在常溫常壓下使用1064nm波長的脈沖激光轟擊目標靶與乙醇流動相的固液界面來連續制備含有碳納米管的溶膠，進而除去乙醇相得到碳納米管，其中目標靶為石墨與fe 、 ni等金屬催化劑混合壓製成的靶片； cvd基體法是使用自製的六方介孔mcm - 41多孔材料為基體，負載fe催化劑活性組分，通過cvd法催化裂解c2h2來生長碳納米管。
  17. The software system investigated in this thesis is used to control the trace heavy metal determination instrument to run the test and analyze data, the software system consists of several modules including data communication data preprocess pre - treatment respecting to real - time performance data storage, etc. the communication between the instrument and the server is based on serial port rs - 232 or ethernet port and the communication among the modules in the software system is based on the message mechanism in windows

    並通過儀器對pb和cu混合溶液檢測的實驗，驗證了聯用多種演算法可以自動對數據進行有效的處理。在對管理控制部分的論述中，文章研究分析了目前集群系統廣泛採用的消息傳遞機制，並論述軟體系統如何使用消息機制協調軟體各個功能模塊的運作。在系統與主機的通訊模塊的設計中，文章論述了如何使用windowsapi函數實現系統的串列通訊介面和ethernet介面。
  18. Standard test method for ph of water extractions of halogenated organic solvents and their admixtures

    鹵化有機溶劑及其混合物水萃取液ph值的標準試驗方法
  19. The pp / gpp / eg electrically conductive nanocomposites with ? c of 6 wt %, which was much lower than that of corresponding electrically conductive composites ( 11 wt % ) prepared via conventional melt - mixing, were firstly achieved via solution intercalation

    首次採用溶液插層法成功制備了pp gpp eg導電納米復合材料，其_ c值為6wt ，明顯低於常規熔體混合法制得相應導電復合材料的_ c值（ 11wt ） 。
分享友人
分享到 Line

分享到臉書