渦狀發形 的英文怎麼說
中文拼音 [guōzhuàngfāxíng]
渦狀發形
英文
swirl-
Three kinds of trapezoid, delta and airfoil shaped vortex generators are designed based on traditional, sub boundary layer and micro - vortex generators conceptual design, to study the influence of the shape, height, aspect ratio, chordwise position, spanwise position and direction angles of vortex generators on boundary layer separation control
（ 5 ）綜合分析研究了渦流發生器的工作原理和設計原則。根據國內外資料，研究了渦流發生器形狀、高度、展弦比、尖削比、弦向位置、展向位置和方位角等因素對附面層分離控制效果的影響。Numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區Abstract : numerical simulation by cfd was carried out to understand the hot current behavior in a tunnel with longitudinal ventilation. it becomes clear that fire source modeling is very important because the hot current behavior is strongly affected by the fire source position and is sensitive to methods in the modeling of the fire source. the flame area which has developed from the fire source is an area of chemical reaction caused by combustion. even if grids in the vicinity of the fire source are made fine, it was difficult to simulate the heat generation area with consideration to this chemical reaction through using a method for setting the heat release rate simply on the fire source surface. therefore, we proposed a method adopting the knowledge on flame shape under the longitudinal ventilation and incorporating it into numerical simulation and it showed a good agreement with the experimental results. it was shown through experiments in a tunnel with longitudinal ventilation that the hot current developed toward the tunnel center downwind from the fire source near a wall. the cause was investigated by numerical simulation and it became clear from the results that the spiral air by the fire plume created a vortex in the crevice between the wall and the plume
文摘:運用cfd進行數字模擬，以了解縱向通風隧道內熱煙氣流的特性.通過模擬發現對火源進行模擬非常重要，熱煙氣流特性受火源位置的影響很大，並且對火源模擬方法很敏感.火源生成的火焰區是燃燒引起的化學反應區域.即使火源附近的木垛排列完好，也很難在考慮這些化學反應條件下模擬熱生成區域.建議考慮縱向通風隧道內火焰形狀並對它進行數字模擬.模擬結果與試驗結果非常吻合.試驗證明，在縱向通風隧道內，熱煙氣流從靠近墻體火源處順風向隧道中心蔓延.數字模擬結果發現，火災羽流造成的螺旋上升空氣會在墻體和羽流之間形成一個渦流區An aeroengine power - turbine 1 ( superscript st ) stage rotor shrouded blade is taken for an example in the article, tightness of shroud and contact force 、 blade body stress under working state and assembly state are calculated by finite element contact analysis method, influence of working load ( temperature and centrifugal force ) is mainly analyzed
摘要以航空發動機動力渦輪一級帶鋸齒形葉冠的轉子葉片為例，用有限元接觸分析方法對裝配和工作狀態下的葉冠緊度和葉冠接觸力、葉身應力進行了計算和分析，著重考察了工作載荷（溫度和離心力）對葉冠接觸力的影響。The advanced development on the new kinds of scroll profile has become the research focus in the profile design. used a new type scroll compressor of the combination profile in this paper, a scroll is constructed following this : the inner turn consists of the standard involute of circle, and the same to the outer turn. then the middle turn is one of arc
本文所研究的新型組合曲線渦旋壓縮機最內圈以基圓漸開線構成，中間段以圓弧過渡，最外圈由圓漸開線構成，能發揮不同型線的優勢，是一種能滿足多性能較優要求、形狀性態良好的渦旋型線，與傳統的基圓漸開線構成的渦旋壓縮機相比，具有效率高、泄露量少、體積利用系數大等優點。The enterprise china petroleum & chemical corp. is well - known and engaged not only in beijing, but also in the specialized industries of its sphere of activity, with catalytic, titanium, efficient and at the same time with clearing, preparation and polystyrene a competent partner
該集團充分準備好渦輪發電機、發生器、發生爐、發電機、相、相位、階段、狀態、形象、位以及容易、靈巧、設施、設備、裝備、工具和反應反作用范圍內進行建議咨詢的信息。分享友人