測量噪聲 的英文怎麼說

中文拼音 [cèliángzàoshēng]
測量噪聲 英文
measurement noise
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 噪 : 動詞1. （蟲或鳥叫） chirp 2. （大聲叫嚷） make noise; make an uproar; clamour
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  1. During simulation of kinematic calibration of virtual axis machine tool, indirect method is used for measuring its position and orientation ; meanwhile jacobean matrix regrouping method is used instead of arduous optimization to avoid measurement noise maginification

    摘要在對虛擬軸機床進行運動學標定的模擬計算過程中，採用間接測量法對虛擬軸機床的運動進行間接測量，然後通過矩陣重構的方法來解決測量噪聲的干擾問題。
  2. The research analysed the influence of observational noises about temporal correlation, and gives recursive formula of kalman filtering

    分析了測量噪聲時間相關對卡爾曼濾波結果的影響，給出了觀測噪聲時間相關時的卡爾曼濾波遞推公式。
  3. On account of the ccd camera mounted on the spatial robot end possesses rather big random measured error, for this reason, a new model of error that includes random measurement error was rebuilt, and it takes the non - geometric parametric error - backlash of transmission links into consideration

    由於空間機器人末端安裝的ccd相機具有較大的隨機測量誤差，因此，重新建立了包含隨機測量噪聲在內的新的誤差模型，它考慮了機器人非幾何參數誤差傳動環節的回差。
  4. Thirdly, data processing software is programmed with median method filter to decrease the noise, and the stability of indicating value is improved

    第三，編制了測量數據處理軟體，採用中值濾波方法對測量噪聲進行有效抑制，提高了監測實驗裝置的示值穩定性。
  5. When the survey data sampled by multiple sensors are adopted to estimate the parameter under the interference of measurement noise, the multisensor data fusion demands timeliness and spatiality

    摘要當採用分佈在不同空間位置上的多傳感器觀測值對測量噪聲干擾下的參數進行融合估計時，數據融合存在時間性與空間性。
  6. The correlations between measurement noises and processing noises are added to the gain matrix of tracking filter, so information that can describe multi - sensors fusion systems is increased

    在跟蹤濾波器的增益陣中引入測量噪聲與過程噪聲的相關量和測量噪聲之間的相關量，增加了描述多傳感器融合系統的信息量。
  7. Description and measurement of environmental noise - guide to application to noise limits

    環境噪聲的描述和測量.噪聲極限應用指南
  8. The robustness of variable structure guidance to line of sight rate measurement noise

    視線角速度測量噪聲對變結構制導魯棒性的影響分析
  9. This paper presented a ml estimator for the estimation of high - frequency sampling noise model to solve the problem that high - frequency sampling suffer from both additive noise and time jitter error estimation

    摘要針對高頻數字采樣中的附加噪聲和時間抖動誤差估計問題，給出了高頻數字采樣測量噪聲誤差的最大似然估計方法。
  10. The result showed that the maximum likelihood algorithm possesses higher stability and suitability on the random measured noise

    結果表明極大似然演算法對隨機測量噪聲具有更高的穩定性和適應性。
  11. In the processing of measurement, the measurement data always consists of measurement error by the influence of random disturbed signal and measurement error. it is necessary to process and revise the measurement data, and get it " s estimate value

    在電網監測過程中，由於有測量噪聲和隨機干擾信號的影響，實際的量測數據往往存在誤差，這就需要對監測數據進行處理和校正，從中得到所需要的各種參量的估計值。
  12. The control objective of this method can be a time variant function or an equilibrium, this method is not affected by the initial condition of the system, the method also demonstrates robustness against model error and measurement noise

    該方法的控制目標可以是時變函數或平衡點，控制不受初值限制，對模型誤差和測量噪聲具有一定的魯棒性。
  13. Analysis in theory and data processing show that the dgps positioning error comes from the effect of multipath mostly, and rtk positioning error comes from the effect of multipath and the receiver noise

    理論分析和數據處理結果表明： dgps的定位誤差主要由多徑效應引起，而影響rtk定位誤差的主要因素包括接收機的測量噪聲和多徑效應。
  14. Reverberation room is the special test room that is used in acoustics, in the measurement of sound absorption coefficient in random incidence and determination of sound power levels of noise sources, the reverberation room is used very extensively

    摘要混響室是聲學專業的實驗室用房，它在測量聲波無規入射時材料的吸聲系數和測量噪聲源的聲功率級中得到了廣泛應用。
  15. A new method of noise reduction is proposed in this paper

    本文提出了一種消除混沌測量噪聲的新方法。
  16. Machine tools. conventional working conditions for measurement of noise. milling machines

    機床.測量噪聲的常規工作條件.銑床
  17. Machine tools. conventional working conditions for measurement of noise. turning machines

    機床.測量噪聲的常規工作條件.車床
  18. Chip removing machine - tools. conditions of working for measurement of noise. general conditions

    除屑機床.測量噪聲的工作條件.一般條件
  19. Safety of industrial trucks - test methods for measuring noise emissions ; german version en 12053 : 2001

    工業用卡車的安全性.測量噪聲排放的試驗方法;德文版
  20. The simulation study showed that the approach could minimized the influences of noises

    模擬研究表明，採用該方法可以克服測量噪聲對傳感器動態補償環節的影響。
分享友人
分享到 Line

分享到臉書