測量控製程序 的英文怎麼說

中文拼音 [cèliángkòngzhìchéngxù]
測量控製程序 英文
measurement control procedure
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 控 : 動詞1 （告發;控告） accuse; charge 2 （控制） control; dominate 3 （使容器口兒朝下 讓裏面的液體慢...
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  • 程序 : 1 （進行次序） order; procedure; course; sequence; schedule; ground rule; routing process 2 [自動...
  1. And ad - link acl - 8112hg data acquisition card is used in gas road exchanging controlling to make this exchange reposefully in the system experiments, tests are given by system control programme

    在預對準實驗方面，編制控製程序，利用光學顯微鏡測量對心和對缺口偏差，計算系統對準重復精度，結果達到了技術要求。
  2. According to the request of this subject, we have developed the system hardware and software for the slave device and the inspection software running on the pc. in this paper all of the followings is illustrated detailedly, such as the research on the principles of measurement and its realization, three means of water - level measurement that are separately based on photo electricity coder, pressure sensor and potentiometer ; selection of the microchip, we choose an advanced integrated soc ( system on chip ) microchip c8051f021 as the main controller ; realization of signal sampling, processing and its conversion in the mcu ; application of high precision 16 bits adc cmos chip - - ad7705 in our system, designing its interface with the microchip and relevant program ; using a trickle charge timekeeping chip ds1302 in the system which can provide time norm and designing of its i / o interface and program ; additionally, a 4 ~ 20ma current output channel to provide system check - up using ad421. in the system, ad421, ad7705 and the microchip compose spi bus ; to communicate with the master pc, here we use two ways which are separately rs232 and rs485 ; moreover, there are alarm unit, keyboard unit, power supply inspection unit and voltage norm providing unit in the system

    針對研製任務的要求，課題期間研製了下位機系統硬體和軟體，開發了上位機監控軟體，其中所作的具體工作包括：測量原理的研究和在系統中的實現，在本次設計中用三種方法來進行水位測量，分別是旋轉編碼器法、液位壓力傳感器法和可變電阻器法；主控晶元的選擇，我們選用了高集成度的混合信號系統級晶元c8051f021 ；實現了信號的採集和處理，包括信號的轉換和在單片機內的運算；高集成度16位模數轉換晶元ad7705在系統中的應用，我們完成了它與單片機的介面設計及程序編制任務；精確時鐘晶元ds1302在系統中的應用，在此，我們實現了用單片機的i o口與ds1302的連接和在軟體中對時序的模擬，該晶元的應用給整臺儀器提供了時間基準，方便了儀器的使用；另外，針對研製任務的要求，還給系統加上了一路4 20ma模擬信號電流環的輸出電路來提供系統監測，該部分的實現是通過採用ad421晶元來完成的，本設計中完成了ad421與單片機的spi介面任務，協調了它與ad7705晶元和單片機共同構成的spi總線系統的關系，並完成了程序設計；與上位機的通信介面設計，該部分通過兩種方法實現： rs232通信方式和rs485通信方式；系統設計方面還包括報警電路設計、操作鍵盤設計、電源監控電路設計、電壓基準電路的設計。
  3. Records test data, applying statistical quality control procedures

    通過運用統計質量控製程序記錄檢測數據。
  4. The fuzzy - pid controller with self - tuned parameters is finally designed out. the dissertation introduces the performance parameters of plvc4 programmable logical controller for valve and its programming software openpcs. connects it to the computer by serial communication and have the computer monitoring program

    閥用可編程式控制制器用串口通訊線與計算機連接，在其編程軟體openpcs環境下用st語言編寫油源系統控製程序，並編制計算機監控程序實現參數在線調整和測量狀態監控。
  5. For the measurement of analog signals such as voltage and current of astg, a filter card for pre - disposing is designed, in order to improve real - time performance, algorithms for ac analog sampling is simplified, and a compensation algorithms for phase error due to sequence - sampling is brought forward. for the measurement of impulse - width signals such as rotor - speed and rotor - position - angle, an intelligent interface card based on isa bus is designed. all programs for measure and control based on c + + are compiled and debugged and the flow for system debugging is summarized

    為了提高實時性，對交流采樣演算法進行了簡化，並提出了由於非同步順序采樣所造成的相位誤差的補償演算法；針對轉速、轉子位置角等脈沖寬度信號的測量，深入分析了測量原理，設計了基於isa總線的智能介面卡；編制和調試了基於c + +的全部測量控製程序；完成了整個系統的調試，並總結了調試方法。
  6. Predictive control is a form of control in which the current control action is obtained by on - line solving open - loop optimal control problem, and the above procedure is repeated based on new state and out measurements at the next time

    預測控制通過在線求解一個有限時域開環最優控制問題來獲得最優預測控制序列，並將當前時刻的控製作用於對象，在下一采樣時刻基於新的狀態或輸出測量值重復上述過程。
  7. What ' s more, the methods of using external code in labview are elaborated. in addition, an input - optimizing design method is put forward. the simulation result shows that this algorithm produces a marked effect finally, a new design of the control system of adjustable pressure casting is proposed

    然後，提出一種在測試計算機實現的輸入信號設計演算法，對輸入的期望信號進行處理，在不增加控製程序計算量和控制迴路周期時間的前提下，使系統的實際輸出符合設計要求。
  8. Moreover the result realizes real - time power system hamonic analysis based on a / d conversion drivers, control programme and algorithm sub - programme

    並編寫a d轉換驅動程序、控製程序和演算法子程序，將它們應用於諧波測量單元，從而完成電力系統諧波分析。
  9. It ’ s already becomes one of the important developing direction to set up auto test system by programmable device with gpib and change the characteristics of traditional device that manual and used in signal device, and also do good to exertion of device function. but most programmable device produced in our country didn ’ t deploy gpib interface panel, which is an disadvantageous factor to make up auto test system. the gpib interface panel designed in this paper can be transplant easily and it ’ s software control completely accord with ieee488. 2 interface criterion, just small program

    本文系統剖析了ieee488規范，並在此基礎上深入地研究了基於ieee488規范的自動測試系統的組建過程，自動測試系統的測試軟體開發流程，並結合具體實例編制出基於ieee488規范的自動測試系統的通用控製程序，該程序可以靈活方便地應用到各種程式控制儀器組成的自動測試系統當中，從而使組建自動測試系統更加便捷，提高了測量工作的速度和效率。
  10. Interfaces and basic data link control procedures for serial measurement data communication ; start - stop - transmission, point - to - point connection

    串列測量數據通信用介面和基本數據鏈接控製程序.第1
  11. Since a self - timed method is proposed to reduce the requirements of controller, the area is only 72mm x 43mm n a 0. 25mm 1p5m cmos technology, and the capability of setup / hold time measurement is provided in the meanwhile

    我們所提出的是一種自動時序的方法，也因此不需要額外的控制線路，所以在0 . 25微米的cmos製程下的面積只有72微米乘以43微米，同時我們的線路也能夠量測設定時間與保持時間。
  12. The 80c196kc single chip microprocessor, electronic switch array, cpld, large capacity ram were integrated into the interface card. the detection operation is intelligent and automatic. the control software and the virtual instrument panel were designed in visual c + +, different messages were sent through serial port

    在檢測系統中設計了具有高速并行數據採集及處理功能的介面卡，介面卡上採用80c196kc單片機、電子開關陣列、大規模門陣列（ cpld ） 、大容量存儲器等器件，實現了智能化、自動化檢測；在微機軟體設計上，運用visualc + +語言編制了虛擬儀器面板程序和控製程序，通過微機串口向單片機發送各種信息。
  13. The organization shall establish and implement procedures for the ongoing identification of hazardous substances used in the products and the manufacturing processes, and implement necessary control measures

    組織須建立並施行對產品和製造流程中的有害物質進行持續識別的程序，並進行必要的控制測量。
  14. The application program is used to provide a platform for the doctors to examine patients ’ blood viscosity for meeting the demand of clinical test. the application program mainly includes these models as follows : data processing, results analysis, data management and so on

    步進電機控製程序主要完成脈沖分配和轉速控制兩個作用;應用程序主要是面向醫院相關科室的醫務工作人員，提供一個對病人血液濃度進行測量的平臺，滿足臨床檢驗的基本要求。
  15. According to runyang bridge engineering, the oop technology is used to designing and developing runyang bridge safety monitoring assist decision - making system. the system makes the setting out surveying and safety monitoring of lower part structure runyang bridge realize intelligence data management, information analysis and assist decision - making. bridge management with reliable base is provided and the bridge construction qualities and safety status can be judged and decided

    從潤揚大橋工程實際出發，利用面向對象的程序開發技術，設計並研製了潤揚大橋安全監控輔助決策系統，使潤揚大橋工程的施工測量和下部結構安全監測實現智能的數據管理、信息分析和輔助決策，該系統能為管理部門對橋梁的施工質量和安全狀況作出評判為輔助決策提供參考依據。
  16. The system uses a new replaceable chip and has realized the chip separated from the flow injection pool. and according to the new chip, the system is designed to employ a new flow injection pool which has a compact structure. in addition, the new system strengthens the function of the control software and puts automatic data - treating into practice

    改進后的系統採用激勵光源正面照射的方式，增強了光電流的響應；同時系統採用新型的可替換式laps晶元設計，實現了多個laps晶元共用一個流通測量池；系統還針對新的晶元設計了流通測量池，該測量池結構緊湊合理，真正實現流通檢測；另外系統還增強了主機控製程序的功能，實現了實驗數據自動化處理，並優化了系統參數設置。
  17. Audit subcontractor quality system / program, including installation / inspection / testing procedures and records, engineering document control, and non - conformance tracking and resolution

    審查分包商的質量控製程序，包括安裝/檢驗/測試步驟和記錄，規劃文件管理及不合格追蹤和解決問題
  18. Audit subcontractor quality control program, including installation / inspection / testing procedures and records, engineering document control, and non - conformance tracking and resolution

    審查分包商的質量控製程序，包括安裝/檢驗/測試步驟和記錄，規劃文件管理及不合格追蹤和解決問題
  19. Audit subcontractor quality system / program ， including installation / inspection / testing procedures and records ， engineering document control ， and non - conformance tracking and resolution

    審查分包商的質量控製程序，包括安裝/檢驗/測試步驟和記錄，規劃文件管理及不合格追蹤和解決問題
分享友人
分享到 Line

分享到臉書