測量軸 的英文怎麼說

中文拼音 [cèliángzhóu]
測量軸 英文
sensitive axis
  • 測 : 動詞1. （測量） survey; fathom; measure 2. （測度; 推測） conjecture; infer
  • 量 : 量動1. （度量） measure 2. （估量） estimate; size up
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 測量 : measure; survey; gauge; meter; measurement; measuring; surveying; mensuration; metering; gauging;...
  1. The method of measuring attitude for aerocraft

    飛行器三軸姿態測量方法
  2. Verification regulation of instrument for measuring place and parallel of radial ball bering outes race

    深溝球軸承套圈滾道直徑位置測量儀檢定規程
  3. Automatic eletronic biaxial tiltmeter

    自動電子雙軸傾斜度測量儀
  4. Measure the clearance of bearing by pressing lead wires

    用壓鉛法測量軸承間隙。
  5. Measured clockwise from the x - axis and ends at

    （從x軸順時針測量）開始，到
  6. Methods. apparent glucose diffusivity measurements were performed on 10 axial and 10 radial af specimens from bovine coccygeal discs. the dependence of diffusivity on compression was determined using 3 levels of strain ( 0 %, 10 %, and 20 % )

    方法：測量來自牛尾骨椎間盤纖維環10個軸的和10個輻射的樣品來獲得葡萄糖近似擴散系數。壓縮狀態下的擴散系數決定於3個等級的拉伸（ 0 % ， 10 % ，和20 % ） 。
  7. A noncontact 3 - d position measurement system is introduced in this thesis. the system is composed of a planner array ccd detector, real time image analysis and quick data calculation system, which can survey the positional relationship between the haloid lamp objects on the emissive vehicle and the measuring system on the loading vehicle

    本文研究了一種簡單、新型的非接觸三維位置測量系統，該系統由一組ccd探測器、實時圖像處理及快速數據解算系統組成，對發射車上鹵鎢燈目標在測量坐標系中的三維坐標x 、 y 、 z值和發射車軸線相對測量坐標軸的夾角進行測量。
  8. Sonographic examinations of the pancreas were performed by sagittal scanning at the epigastrium ; the long axis and short axis of the oval cross - sections of both the pancreatic head and body were measured

    檢查測量的方式是在上腹部作縱向掃描，可以分別得到胰臟頭部與體部之圓形縱切面造影，進而分別測量胰臟頭部與體的長軸與短軸，一共為4個胰臟因數。
  9. First, the wheelset is fixed and rotated by the device used hi vehicle depot as usual. second, the center line of wheelset axis is determined by a device called axis - center probe. last, the acting device for sensor can draw a whole felloe profile, which is made up of parallel - pole device and rotating - probe

    鑒於此，本文給出了一種全新的測量方案：採用車輛段普遍使用的轉輪器實現被測輪對的定位；採用車軸基準探尺測定被測輪對的軸線；採用並聯式伸縮機構和旋轉測頭作為傳感器的執行機構，測定輪輞斷面的輪廓線。
  10. Gooseneck to be dismantled, examined and measured. ball bearing and glands in the socket of gooseneck to be cleaned, examined, repaired or renewed if necessary, greaed and refitted

    鵝頸銷拆開，檢查，測量。鵝頸銷承套中球軸承及格欄清潔，檢查，必要時修理，換新，加牛油后裝妥。
  11. After analysing several kinds of light - weighting structures through ansys, hexagonal speculum structure is confirmed. in the aspect of the controling of speculum, the paper adopts the brushless dc motor which is partial assembled to drive the point speculum and the inductosyn as angle measuring component is selected, the ad2s80a the system is used to get directly angle and angular velocity. double closed - loop speed and position control is designed, as the pid control is the well - developed algorithm, which can achieve stable rotation and precise position control

    在指向反射鏡的擺動控制方面，採用低速性能好的分裝式直流力矩電機作為指向反射鏡的驅動電機，並採用感應同步器作為角度測量元件，運用軸角轉換器ad2s80a進行角度和速度的輸出，採用技術成熟的pid控制方案，進行速度和位置雙閉環控制，以實現指向反射鏡轉動速度的平穩性和位置的精確性。
  12. During simulation of kinematic calibration of virtual axis machine tool, indirect method is used for measuring its position and orientation ; meanwhile jacobean matrix regrouping method is used instead of arduous optimization to avoid measurement noise maginification

    摘要在對虛擬軸機床進行運動學標定的模擬計算過程中，採用間接測量法對虛擬軸機床的運動進行間接測量，然後通過矩陣重構的方法來解決測量噪聲的干擾問題。
  13. It is appropriate for measuring end temperature of bearing liner or other works, e. g., push bearing liner of steamer, supporting bearing liner or push bearing liner of electromotor main axis, bearing liner of coal pulverizer, bearing liner of high efficient feed water pump, bearing liner of compression machine and kinds of other objects inpetrochemical plant

    適用於測量軸瓦或其它機件的端面溫度，如：汽輪機推力軸瓦，電機主軸支持瓦推力瓦，磨煤機大瓦和高效給水泵軸瓦石油化工廠壓縮機軸瓦和各種機件物體的表面測量。
  14. Exciting method is used to measure the damping, the four damping coefficients of the radial part and a damping coefficient of the thrust part can be obtained though hammering the testing bearing which is in a equilibrium position. based on the testing data, the dynamic characteristic curves of the radial - thrust floating ring hybrid bearing are drawn and compared with the theoretical curves

    採用激振法測量軸承的阻尼，對處于平衡位置的測試軸承分別沿水平方向、上45度方向及軸向進行錘擊，根據錘擊法原理求得各個轉速下軸承徑向部分內、外膜總阻尼系數以及推力部分內、外膜總阻尼系數。
  15. Web tension measurement via measuring bearing journals

    通過測量軸承軸頸來測量紙幅張力
  16. Depending on the individual situation the electronic equipment can be combined with different transducers to measure force measuring axles, tensile compressive transducers

    在特殊的情況下電子設備可以和不同的力傳感器測量軸，拉力壓縮里換能器結合使用來測量。
  17. The greatest lateral force effect in the plane perpendicular to the measuring axis is to be stated

    作用在與測量軸垂直的平面上的最大側力作用是一定的。
  18. Greatest force in the direction of the axis of measurement that a force transducer with built - in overload protection may take up without the error limits being exceeded on re - use of the transducer up to the nominal force

    在不超過再使用傳感器標準力的誤差范圍的情況下，帶有過載保護的力傳感器能夠承受的測量軸方向的最大力。
  19. Resonant frequency at which the unloaded transducer without force translation parts oscillates after shocklike excitation in the direction of the measuring axis, whereby the basis intended for securing it is coupled to a sufficiently large mass

    沒有力平移元件的空載轉換器在測量軸方向上受到類似震動的激勵下會產生震蕩。在基本共振頻率下會對固定基礎造成很大傷害。
  20. Maximum force in the direction of the force transducer s axis of measurement, up to which a defined and repeatable relationship exists between force and output signal, but where protection against overloading that may be present does not yet operate

    在力轉換器測量軸的方向上的最大力。小於這個力時，力和輸出信號之間有定義的可重復的關系。但不符合有過載保護的情況。
分享友人
分享到 Line

分享到臉書