準穩態流動 的英文怎麼說

中文拼音 [zhǔnwěntàiliúdòng]
準穩態流動 英文
quasi steady state flow
  • 準 : Ⅰ名詞1 （標準） standard; guideline; criterion; norm 2 （目標） aim; target Ⅱ動詞1 （依據; 依照）...
  • 穩 : 形容詞1 （穩定; 穩當） steady; stable; firm 2 （穩重） steady; staid; sedate 3 （穩妥） sure; rel...
  • 態 : 名詞1. （形狀; 狀態） form; condition; appearance 2. [物理學] （物質結構的狀態或階段） state 3. [語言學] （一種語法范疇） voice
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  1. In the positioning servo - system, which generally is configured by the d. c. pulse width modulator ( pwm ) velocity governing system and position servo - loop, the parameter perturbance of pwm velocity loop really exist by reason of such as the load behavior ; power voltage supply ; operating setting value, etc. 1, 2 ， and it cannot be ignored. by using the identification technique to form the mathematical model of the system, authors have confirmed the facts. therefore, to design the discrete sliding mode controller ( dsmc ) of the positioning servo - system, the perturbed parameters value bounds of the pwm velocity loop, which is as the controlled plant of position servo - loop, should be accounted. consequently, the design principle of dsmc for accounting system with parameter perturbance is proposed by the authors. the proposed method can ensure the stability of system with parameter perturbance and the behavior of non - overshoot, fast precise positioning. in order to reveal the effects of the design method, the comparative research work is done by the authors. also, it has been tested in an industrial experiment, the results proved it is satisfactory

    由直流脈寬調速系統（ pwm ）和位置環構成的定位系統中，速度環的參數隨負載特性；電網電壓；給定工況而攝動是不容忽視的.作者通過系統辨識建模也證實了這一事實1 ， 2 .因此在設計位置環的離散滑模控制時，必須針對速度環（即位置環的控制對象）的參數攝動范圍採用「對象參數攝動離散滑模控制器的設計方法」 ，以確保系統在參數攝動時的穩定性和快速、無超調、準確定位的優良動態品質.為剖析該設計方法的控制效果，本文作了對比性研究，並將該設計方法用於工業試驗中，取得了滿意的結果
  2. During the temperature fields, the results indicate that the processing parameters such as the extrusion velocity, casting temperature, perform preheating temperature, die preheating temperature and so on are important for the temperature fields besides the dwell time. they are must be in concordance each other to the deforming zone is in the quasi - solid state, and the stable semi - solid extrusion is implemented. during the deforming fields, the hyperbolic sine thermo - rigid - viscoplastic fem model is selected according to the forming feature of the process, and the variations of the stress - strain fields are studied

    在溫度場的模擬中，模擬結果表明，保壓時間是影響製件成形質量的關鍵因素之一，擠壓速度、液態金屬澆注溫度、預制體預熱溫度和模具預熱溫度等工藝參數對溫度場的影響也很大，需進行參數之間的協調，只有當變形區內部始終維持準固態時，才能實現穩定的液-固擠壓成形過程；在變形場的模擬中，根據液態浸滲擠壓的成形特徵，選用了雙曲正弦剛-粘塑性有限元計算模型，研究了變形過程中應力應變場的變化規律，研究了模角對變形和金屬流動的影響及變形力的變化過程和其影響因素。
  3. Abstract : clibrating turbine flow meter is traditionally static meter - factor. this thesis introduces the theory and practice method of calibrating the dynamic character of turbine flow meter

    文摘:渦輪流量計傳統上只進行穩態校準，即只校準其（穩態）儀表系數。本文闡述了校準渦輪流量計動態響應特性的理論和實施方法。
  4. The next large block of lectures covers quasi - one - dimensional flow, followed by a discussion of disturbances and unsteady flows

    接下主要內容介紹了準一維流動，接著討論擾動流與非穩態流。
  5. The non - insulated topology characteristics, steady and dynamic principles, parameter design of vrm applied for low - input voltage situation are mainly analyzed

    本文重點分析、研究了應用於低電壓輸入的vrm非隔離性同步整流準方波buck變換器拓撲特性、穩態和動態性能，參數設計等。
  6. The paper describes a cw, non - cooling, digital all - solid - stated ld pumped nd : yvo4 driver which adopts microprocessor control, stability power of laser feedback and laser output power about 10mw. the system is composed of constant current source, soft diagram, protection, pulse schematic and laser power feedback loop. by combining appropriate hardware and software, we achieved, in our driver, a variety of protection features including the ability to suppress transients and reduce noise, relay soft and hardware over - current protection and overvoltage shut - off, we have obtained a continuously adjustable laser power output with high accuracy and stability

    介紹一種採用單片機控制的連續運轉無製冷、數字式光反饋穩功率全固態激光器驅動電源，其輸出激光功率在10mw左右，系統包括恆流源、保護電路、脈沖驅動控制、光反饋穩功率控制等部分，結合硬體及軟體實現了激光二極體的可靠保護以及光功率穩定、準確輸出及在穩光輸出情況下，實現激光器的內外調制，並取得了一些有價值的研究成果。
  7. The main ideas in this dissertation are motivated from industry applications, which are listed as follows : 1. quasi - steady - state linear data reconciliation is defined for mass balance of a whole factory by taking the storage capacity of devices into consideration

    以全廠物流數據協調為背景，針對流程工業特性，綜合考慮容性節點貯液量的動態變化，引入了線性準穩態數據協調。
分享友人
分享到 Line

分享到臉書