溢流型 的英文怎麼說

中文拼音 [yìliúxíng]
溢流型 英文
down flow type
  • 溢 : Ⅰ動詞（充滿而流出來） overflow; spill Ⅱ形容詞（過分） excessive
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 溢流 : effluent flow
  1. This paper introduces the surface forming technology for pocket concrete overflow weir, analyzes and compares construction technique for two types of gate and built - in parts, and presents rating methods for concrete samples when they are less than 30 groups

    摘要現介紹了小型混凝土溢流堰堰面成型工藝，分析比較了兩種閘門埋件施工工藝，提出了數量不足30組時的混凝土試塊評優的方法。
  2. The typical velocity field and the pressure on the step surface of the stepped spillway are measured using the laser doppler anemometer and the piezometer tube respectively

    採用多普勒激光測速儀和測壓管分別對階梯溢流壩面典型速度場和階梯表面壓力進行詳細測量。
  3. According to differences of construction process, boundary condition, temperature and stress of two schemes extending 3m deep short seam on upstream face in the middle of rcc overflow section and no short seam are calculated, what " s more, in this paper the equivalent line drawing of stable temperature field and unstable temperature field during construction and operation period and the duration curve drawing of typical points " s temperature and stress are plotted, and the results of peak and minimum on temperature in every month and maximum on tensile stress are attained

    根據施工過程和邊界條件，對溢流壩段中間上游面增設3m深短縫和不設短縫兩個方案進行了溫度和應力計算，並繪制出穩定溫度場等值線圖及施工期、運行期非穩定溫度場等值線圖，典型點溫度和應力歷時曲線圖，逐月最高、最低溫度和最大拉應力及相應位置等成果。
  4. Based on analysing all kinds of sediment silting basins and their suitable conditions, the traditional sedimentation basin has been improved in three aspects, i. e., setting an adjusting flow board in the fore of setting basin, adding a spillway trough along the flow direction, and redesigning the flush gallery by adding auxiliary flushing facilities

    摘要在對各種類型沉沙池及適用條件進行分析的基礎上，通過在沉沙池的首部加調流板、在溢流堰上沿水流方向設溢流槽、對沖沙廊道進行改進並設置輔助沖沙設施這3個方面對傳統沉沙池進行了改進。
  5. In order to calculate quantitatively the process of rainfall - runoff, the css model of zhang cha catchment is developed based on epa ’ s swmm ( storm water management model ) in this paper. and then calculate cso spill water quality 、 spill volume and spill time at different intercepting ratio using the developed swmm, and analyze the effect on them by intercepting ratio

    為了實現上述降雨?徑流過程的定量計算，本文引入美國環保局的城市暴雨水管理模型（ swmm ）建立了佛山市張槎排水區的合流制排水系統模型，使用該模型計算了不同截流倍數時溢流污水的水質、水量以及溢流時間，並分析了截流倍數對它們的影響。
  6. Based on genetic analysis, the volcanic rocks in this area are divided into four lithofacies : explosive, overflow, intrusive and volcanic sedimentation facies, in which the explosive and overflow are favorable facies for reservoir development

    根據成因分析，將該區火山巖劃分為四種巖相類型：爆發相、溢流相、侵出相及火山沉積相，其中爆發相和溢流相為儲層發育的有利相帶。
  7. Three methods of scouring are applied, such as cold pad - batch, pretreatment in overflow machine, and pretreatment in slack bleaching and scouring machine, which are suitable for different batches and printing patterns

    介紹了三種前處理煮練工藝：冷軋堆、溢流機前處理和松式繩狀練漂聯合機前處理，可適用於不同批量和印花花型。
  8. The process of effluent flow during loading in self - propelled trailing suction hopper dredgers was simulated by way of physical modeling and was measured and analyzed by using the flow rate and concentration of spoil in the hoppers, particle sizes of sediments at the inlet and outlet of the effluent flow pipe and hopper volume as the major control parameters

    摘要通過物理模型試驗模擬自航耙吸挖泥船裝艙溢流施工過程，以艙內流速、艙內濃度、溢流進出口泥沙粒徑、裝艙量幾方面為主要控制因素，進行實測、分析，並比較自航耙4種常用裝艙裝置的消能效果。
  9. Straight moving type relief valves, mainly valve disc, valve body, spring - loaded, roof, regulation pole, conditioning nut, and other integral parts

    直動型溢流閥，主要有閥芯、閥體、彈簧、上蓋、調節桿、調節螺母等零件組成。
  10. The result show that the position of free surface is higher because of frusta of brake, especial obvious in the head of frusta of brake ; flux coefficient and pressure on dam are quite influenced by type of frusta and 3 a type frusta of brake relative to 2 type frusta of brake has bigger flux coefficient and smaller pressure on dam ; obvious influence of ability of discharge flow for different ratio of thickness of frusta and breadth of brake and pressure on dam reduces with increasing ration of thickness of frusta and breadth of brake, while bigger flux coefficient is obtained when tlb = 0. 2

    結果表明，閘墩河海大學博士論文的存在抬高了水面線的位置，其中在閘墩頭部尤其明顯;墩型對流量系數和壩面壓力影響較大， 3a型閘墩相對於2型閘墩具有更大的流量系數和更小的壩面壓力:不同的墩厚閘寬比t / b對泄流能力也將產生顯著的影響，隨著墩厚閘寬比的增加，壩面壓力降低，而當t / b二0 . 2時溢流壩具有更大的流量系數。
  11. The overflow ratio is an important parameter of the deoiling hydrocyclone

    溢流分率是去油型旋流器的一個重要操作參數。
  12. Devices to prevent pollution by backflow of potable water - air gap with circular overflow restricted - family a, type f

    防飲用水迴流污染的裝置.帶圓形溢流口的氣隙. f型a系列
  13. Devices to prevent pollution by backflow of potable water - air gap with circular overflow restricted - family a, type f ; german version en 14622 : 2005

    防飲用水迴流污染的裝置.帶圓形溢流口的氣隙. f型a系
  14. Devices to prevent pollution by backflow of potable water - air gap with submerged feed incorporating air inlet plus overflow - family a, type c

    防飲用水迴流污染裝置.帶浸入式給水裝有空氣進口和溢流口的氣隙. a類c型
  15. Based on the relocating mesh model, according to heat conduction theory, elastic creep theory and finite element theory, simulation program for roller compacted concrete overflow dam is worked out through 3 - d finite element method

    基於本文提出的計算模型，根據熱傳導理論、彈性徐變理論及有限元理論，作者編制了碾壓混凝土溢流壩溫度場及溫度應力場的三維有限元模擬計算程序。
  16. A parametric analysis of the inviscid effects of leading edge sweep, sidewall compression, width - height ratio, cowl position and inflow mach number on spillage is finished. numerical simulations are completed for a series of inlets at various flight height and velocity. the research indicates that the area of spillage window, which is mainly determined by the position of the cowl, significantly influences the spillage characteristic of the scramjet inlet

    闡明了側板后掠的側壓進氣道設計參數對構型溢流影響;對不同側板配置方式的側壓式進氣道進行了數值模擬，通過對比分析，發現由唇口板的位置所決定的溢流窗面積的大小對進氣道溢流特性的影響顯著。
  17. Finally, being aimed at a certain machine model, a experiment research about the means of relief valve to reduce hydraulic impact is carried out, which prove the founded prove founded mathematics model. also, some pending coefficient are amended and the optimum pressure of relief valve is determined. at the same time, a experiment and emulation research about the means of accumulator to decrease hydraulic impact is carried put, in which the optimum pneumatic pressure and the optimum primitive capacity of accumulator were determined

    最後針對某一具體機型，對用溢流閥方式減小液壓沖擊進行了實驗研究，驗證了所建立的數學模型並修正了待定系數，確定了溢流閥的最優調定壓力；對用蓄能器方式減小液壓沖擊進行了實驗和模擬研究，確定了蓄能器的最優充氣壓力和最優初始容積。
  18. A on - identify model of proportional valve pressure controlled system was established though analyzing the configuration of dbetr type proportional pressure relief valve firstly, and then using classical step response method to identify system parameter, a practicable system simple model was deduced at last

    摘要從dbetr型比例壓力溢流閥結構出發，先建立比例閥控制壓力系統的待辨識模型，再採用經典的階躍響應法辨識系統參數，得到工程上適用的系統簡化模型。
  19. In this paper the temperature field and thermal - creep - stress field in roller compacted concrete overflow dam during construction and operation are simulated and the distribution law of them are systematically studied by an example

    本文通過一典型算例對碾壓混凝土溢流壩施工期和運行期溫度場、徐變應力場進行了全過程模擬分析，較為系統的研究了碾壓混凝土溢流壩施工期和運行期溫度場、溫度徐變應力場的分佈規律。
  20. This paper does simulation analysis on temperature field of baise rcc gravity dam with the software ansys based on the theory of transient temperature field

    摘要根據瞬態熱傳導三維有限元分析基本理論，利用大型有限元軟體ansys對百色碾壓混凝土重力壩溢流壩段一枯二枯施工期的溫度場進行了實時模擬分析。
分享友人
分享到 Line

分享到臉書