溢流調節 的英文怎麼說

中文拼音 [yìliúdiàojié]
溢流調節 英文
bleed-off
  • 溢 : Ⅰ動詞（充滿而流出來） overflow; spill Ⅱ形容詞（過分） excessive
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 調 : Ⅰ動詞1 （配合得均勻合適） harmonize; suit well; fit in perfectly 2 （使配合得均勻合適） mix; adju...
  • 節 : 節構詞成分。
  • 溢流 : effluent flow
  • 調節 : regulate; adjust; monitor; measure; take care of; condition; regulation; adjustment; conditioning...
  1. When the governing valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod increased, meanwhile, it ' s time of rise, time to peak and the governing time all increased. at the same time, the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    當出口節流調速系統的回油路上串接調速閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是增加的，上升時間、峰值時間以及調整時間也是增加的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  2. Straight moving type relief valves, mainly valve disc, valve body, spring - loaded, roof, regulation pole, conditioning nut, and other integral parts

    直動型溢流閥，主要有閥芯、閥體、彈簧、上蓋、調節桿、調節螺母等零件組成。
  3. The proportional relief valve is used to adjust control the pressure of hydraulic oil, therefore controls the brake moment by adjusting the thickness of oil film

    用電液比例溢流閥對控制油壓進行調節，從而調節油膜的厚度來控制制動力矩。
  4. Secondly, the main stuctures of the software and hardware parts of the control system are introduced. principles and realization of the main functional blocks of these two parts are illuminated. on the hardware of the system, parts of control circuit and the design and debugging of peripheral circuits are discussed thoroughly. based on the hardware circuit, the software is programmed with assembly language. dual close loop vector control weth feedback of speed and current are realized. the flow charts of main programme and pwm interrupt service routines are given. the important control strategies of vector control pmsm such as current sensint and scaling, speed sensing and scaling, bector co - ordinate transformation, generation of sine and cosine, pi regulators, svpwm vector modulation and so on are all accomplished in the pwm interrupt sevice routines. in order to unite all the variables in the programme, scaling is used

    硬體方面主要論述了控制電路各部分及外圍輔助電路的設計和調試。在硬體的基礎上，軟體採用匯編語言編程，實現了轉速和電流雙閉環矢量控制。給出了系統主程序和pwm下溢中斷處理程序流程圖， pmsm矢量控制的主要控制策略如電流采樣與定標、速度采樣與定標、矢量坐標變換、 sin和cos值生成、 pi調節、 svpwm波形生成等都是在pwm下溢中斷服務子程序中完成的。
  5. Accorded to the experimental research, under different flow area of flow valve and different adjusted pressure of relief valve, conclusion that the regulation of the pressure p1, p2 in the two cylinder chambers varied with the change of step load were as follows : when the throttle valve was series - connected on the return oil - line in the metering - out control system, under the same flow area and the same adjusted pressure of relief valve, with the incremental quantity of step load, the pressure highly - adjusted capacity of the hydraulic cylinder chamber with piston - rod decreased, meanwhile, it ' s time of rise, time to peak and the governing time all decreased. while the pressure highly - adjusted capacity of the hydraulic cylinder chamber without piston - rod increased

    通過試驗研究得出系統在不同的流量閥開度、不同溢流閥調節壓力（進口壓力）下，液壓缸兩腔壓力p _ 1 、 p _ 2隨階躍負載變化的規律：當出口節流調速系統的回油路上串接節流閥時，隨階躍負載的增加，在相同流量閥開度、相同溢流閥調節壓力的情況下，液壓缸有桿腔壓力p _ 2 （ t ）的超調量是減小的，上升時間、峰值時間以及調整時間也是減小的；液壓缸無桿腔壓力p _ 1 （ t ）的超調量是增加的。
  6. This constant - pressure hydraulic power adopts plvc4 programmable logical controller for valve to control the electro - hydraulic proportional relief valve to adjust the pressure at the entrance of the servo valve and makes it change with the pressure change at the exit thus to keep the pressure difference constant

    此恆壓油源採用閥用可編程式控制制器plvc4控制電液比例溢流閥調節伺服閥入口壓力，使其跟隨伺服閥出口壓力變化，達到入出口壓力差值恆定的目的。
  7. The control system so regulates the valves that they are closed when overflow occurs

    控制系統對閥的調節方式是當發生溢流時它們被關閉。
分享友人
分享到 Line

分享到臉書