溫度度標 的英文怎麼說

中文拼音 [wēnbiāo]
溫度度標 英文
temperature scale
  • : Ⅰ形容詞(不冷不熱) warm; lukewarm; hot; gentle; mild Ⅱ名詞1 (溫度) temperature 2 (瘟) acute ...
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  • : Ⅰ名詞1 [書面語] (樹梢) treetop; the tip of a tree2 (枝節或表面) symptom; outside appearance; ...
  • 溫度 : [物理學] temperature
  1. This article aims at the boiler ' s problems in operation : 1 ) under nominal load, the smoke temperature at the outlet of hearth reaches 1200, far more exceeds 1050 the original designed temperature. this will always result in slag inside boiler and the temperature of overheater ' s pipe superheat, so that boiler cannot take nominal load and all these influence boiler ' s nomal operation heavily, 2 ) this article also studied the reason why the assistant oil becoming necessary when coal changes. during the nomal operation, many factors ( makeup of combustor and its disposal, smirch and encrust of water wall, excessive air coefficient, temperature of primary air, coal type and density of coal dust ) can deviate the designed working conditions, then affect the boiler ' s nomal operation

    本文針對該鍋爐在實際運行中存在的問題:在額定負荷下,爐膛出口超、低段過熱器前煙高達936 ,遠遠超過815的設計值;噴燃器四周水冷壁結焦嚴重,過熱器管壁,無法帶上額定負荷;甚至有時因燃煤質量的變化,必須投油助燃的嚴重情況進行了分析研究。在實際生產過程中,燃燒器的結構、布置,水冷壁的粘污、結垢,過剩空氣系數、一次風、煤種及其濃變化等許多因素都會偏離鍋爐的設計工況,從而影響爐內的傳熱和燃燒,造成爐膛出口超、水冷壁結渣等問題。
  2. Scrap steel will be loaded into steelmaking furnace and molten after sieving and dewetting. if the chemical composition and target temperature of molten steel are satisfied, the molten steel will be poured into ladle and conveyed to continuous caster, then be made as billet with specified length

    廢鋼鐵經篩選去濕,裝入煉鋼爐冶煉融化成鋼水,當達到要求的化學成分及值時,將鋼水倒入鋼水包,送至連鑄機,澆鑄成定尺長的鋼坯
  3. From the scaling law about hot electron temperature given by vh model, the hot electron measured by experiment was reasonable, the temperature was higher than the temperature given by resonant absorption scaling law

    真空吸收是產生高能超熱電子的主導過程,從真空吸收給出的超熱電子率來看,實驗中測量得到的超熱電子是合理的。
  4. Test method for normal spectral emittance at elevated temperatures

    升高準光譜發射的試驗方法
  5. Primary analysis of the temperature index during breeding and transplanting rice seedlings in fangzeng county

    插秧期與產量的初步分析
  6. Electric lamps - standard method of measuring the pinch temperature of quartz tungsten - halogen lamps

    電燈.測定鹵鎢石英燈收縮準方法
  7. Standard test method for brittleness temperature of plastic sheeting by impact

    用沖擊法測定塑料薄板的脆化準試驗方法
  8. Standard method of measuring the pinch temperature of quartz - tungstenhalogen lamps

    測量石英鹵鎢燈夾封部準方法
  9. The results showed that the range of target finishing temperature can be provided and kept on in an energy - saving manner with lower frequency of spray nozzle opening if opening reversely but closing forwardly the cooling valve for inter - stand spray during water cooling

    對兩種截然不同的機架間噴水冷卻閥門開啟邏輯做了計算分析,結果表明,逆向開啟機架間噴水冷卻閥門,順向關閉閥門,能以較少的噴嘴開啟數達到終軋范圍,並且可以節約能耗。
  10. Standard practice for paving uses and application temperatures for road tars

    道路柏油的鋪砌和使用準操作規程
  11. Standard test method for heat - fail temperature in shear of hot melt adhesives

    熱熔膠粘劑剪切試驗中熱斷裂準試驗方法
  12. Standard test method for transformation temperature of nickel - titanium alloys by thermal analysis

    用熱分析法測定鎳-鈦合金轉變準試驗方法
  13. Standard test method for oxidation onset temperature of hydrocarbons by differential scanning calorimetry

    用差別掃描熱量測定法測定烴類氧化開始準試驗方法
  14. Standard test method for gel time and peak exothermic temperature of reacting thermosetting resins

    活性熱固樹脂膠凝時間和最大放熱準測試方法
  15. Standard practice for glass transition temperatures of hydrocarbon resins by differential scanning calorimetry

    用差分式掃描熱量儀測定碳氫化合物樹脂玻璃導熱準實施規程
  16. Standard test method for temperature of freshly mixed hydraulic - cement concrete

    新拌水硬水泥混凝土準試驗方法
  17. Standard test method for indentation softening temperature by thermomechanical analysis

    使用熱機分析法測試壓痕軟化準試驗方法
  18. Standard test method for prediction of asphalt - bound pavement layer temperatures

    預測地瀝青粘合鋪層準試驗方法
  19. An approach of two point temperature correction parameter compensation is presented in this paper, it can compensate the parameter accuracy according to the real - time signal dynamic range, the parameter can be modified near to its theoretical value

    文中探索了一種二次參數補償的兩點方案,由基本公式得到的校準參數值,再依據現實信號動態范圍進行實時精補償,使之更加接近於理論計算值,從而使非均勻性校準的系數精得到較大幅提高。
  20. Standard test method for assignment of the glass transition temperature by thermomechanical analysis

    使用熱機分析測定玻璃轉變準試驗方法
分享友人