溫度斷面圖 的英文怎麼說

中文拼音 [wēndùduànmiàntú]
溫度斷面圖 英文
temperature profile
  • 溫 : Ⅰ形容詞（不冷不熱） warm; lukewarm; hot; gentle; mild Ⅱ名詞1 （溫度） temperature 2 （瘟） acute ...
  • 度 : 度動詞[書面語] （推測; 估計） surmise; estimate
  • 斷 : Ⅰ動詞1 （分成段） break; snap 2 （斷絕;隔斷） break off; cut off; stop 3 （戒除） give up; abstai...
  • 面 : Ⅰ名詞1 （頭的前部; 臉） face 2 （物體的表面） surface; top 3 （外露的一層或正面） outside; the ri...
  • 圖 : Ⅰ名詞1 （繪畫表現出的形象; 圖畫） picture; chart; drawing; map 2 （計劃） plan; scheme; attempt 3...
  • 溫度 : [物理學] temperature
  • 斷面 : section; fracture surface; plane of fracture
  1. As to the video signal, alarm signal, control signal, are all weak electricity signal, exceedingly easily be subjected to the jam, in case the power supply system does not steady, wave propag ation is greatly, the harmonic content of power source overtops, the veins wave factors are great unduly, and even power source equipment breakdown, outputting abnormal, will be about to affect the video signal image effect, and dependability cuts downs to the security and alarming system. we adopt fast fu lye ' s mutation rule - fft alternatives, by the way of carrying fft alternatives to the local junction circuit, regulated power supply, ups ' s power source, and switch power source, thereby diagnose every degree harmonious wave content of power souse, and abnormal coefficient, compared to the normal working situation. thereby diagnose out the working condition of the regulated power supply, ups ' s power source, and switch power source

    如果有供電系統不穩定、波動大，電源的諧波含量過高，紋波系數過大，乃至電源設備損壞、輸出異常等情況出現，將會嚴重影響視頻信號的圖像效果，大大降低防盜系統的穩定性和可靠性，我們採用快速傅利葉變換原理，即fft變換，通過對市電、穩壓電源、 ups電源、開關電源等的電壓信號進行fft變換，從而得出信號中各次諧波的含量及信號畸變系數，並將其與正常工況下的參數進行對比，從而進一步診斷出穩壓電源、 ups電源、開關電源等設備的運行狀況；組成監控系統的設備長期處于工作狀態，往往由於設備散熱條件不好、設備老化故障等原因導致設備表面溫度過高，從而影響設備的正常運行，降低設備的使用壽命。
  2. Firstly, the distortion of rolled piece and the designing method in the beforehand slit pass and slit pass has been analyzed. secondly, based on the research production of predecessor and research of the author, card system selected some corresponding experience formulas such as roll force, roll moment, roll temperature and roll consume, and established spread model in the beforehand slit pass and slit pass and the distribution model of elongation coefficient. subsequently, card system applied the dynamic programming method with minimum roll consume and optimized its pass system

    本文以圓鋼雙線切分為基本實體模型，著重分析了預切分孔型和切分孔型在軋制過程中的變形特點及相應的孔型設計方法；基於前人的研究成果及作者的探索，選擇了相應的軋制力、軋制力矩、溫度及能耗模型，建立了預切分和切分的寬展及延伸系數的分配模型；應用動態規劃法以能耗最小為目標函數對孔型系統進行了優化設計；利用visualbasic6 . 0和microsoftaccess數據庫的連接，建立了數據查詢系統，以visualbasic6 . 0和autocad之間的介面在vb環境下完成了斷面孔型圖的繪制。
分享友人
分享到 Line

分享到臉書