滑動閥 的英文怎麼說
中文拼音 [gǔdòngfá]
滑動閥
英文
absperrschieber-
Turn both handles of the rotary slide valve ( pos. no. 15 ) and the clutch to the emergency position, and the annunciator “ emergency ” is lit on
轉動旋轉滑閥15和離合器手柄到應急位置,指示器「應急「燈亮。Non - lubricated, tapered plug assures tight seal with low breakout torque. constructed of hardened materials with optional hard facing
無潤滑,錐形閥塞確保緊密密封,並且具有很低的啟動扭矩。有硬化材料構造而成,配置備選硬面。Slide one half of the splash guard into the groove on the relief valve body
將防濺保護的一半滑動到安全閥閥體的溝槽上。Slide the other half of the splash guard into the groove on the relief valve body and reassemble the two parts together
將防濺保護的另一半滑動到安全閥閥體的溝槽上,將兩半部件重新組裝在一起。All seating & sliding surfaces hardfaced with stellite 6
所有閥座和滑動件表面都是硬面鎢鉻鈷合金6 。Because of the high flow resistance and the poor flowing ability, the spool valves ca n ' t meet the requirements for high velocity or huge hydraulic equipment
同時由於滑閥流動阻力大,通流能力小,不能滿足高速或大型液壓設備對流量的要求。Dynamic vibration simulation of rotary piston vacuum pump
滑閥真空泵振動平衡的優化設計研究Combination sliding and rotary spool valve
又移動又旋轉的圓柱滑閥Punching tool parts, blocks for edm, scissor parts, circular knives, machine parts, extruding tools, tools for diecasting pulverized materials, pressure plates, sliding parts, valve parts, embossing dies, cutter disks, planer knives for machining of wood, hard metal tipped tools, rolls for cold rolling mills
沖壓工具零件、電火花機床的滑車、剪刀的刃口、環刀、機械零件、擠壓工具、硬模鑄造研磨材料的工具、承壓板、滑動零件、閥門零件、壓花模、圓盤刀、木工中刨刀、切削硬金屬刀片、冷壓滾軸。Parallel slide or double disc valves tend to leak after a short period in this service
平行滑動或雙閥瓣閥門在這種應用場合中經過短暫使用后,容易出現泄漏。Then, lubricate the stem and slide top of the elastomeric seat over the top ( long end ) of stem and push down over the o - rings
然後,在閥桿上加潤滑油,在閥桿頂部(長端處)滑動彈性材料閥座的頂部,將其推到o形環上。Automatic steam stop - check angle - globe valves are best on medium - pressure steam service where the sliding action of the semi - plug disc assembly permits the valve to serve as a shut - off valve, a throttling valve and a check valve
自動蒸汽截止止回閥和角式截止閥適用於中壓蒸汽管道系統,此時半插入式閥瓣的滑動作用使得閥門能夠起到關閉閥、節流閥和止回閥的作用。Cavities for hydraulic fluid power cartridge valves - specification for two - port slip - in valves
液壓動力卡盤式閥的空腔.第1部分:二通鑲套滑動閥規范Due to its inherent design, the parallel slide valve is not subject to thermal binding concerns, resulting in a distinct safety advantage in high temperature service
這種結構的基本特性,決定平行滑動閥門比較不會受到熱附著的影響,因此在高溫應用領域具有顯著的安全優勢。150 300 600 face - to - face dimensions for sliding stem flangeless control valves classes 150, 300, and 600
滑動桿無凸緣控制閥的端面間尺寸In order to prolong the natural life of fracturing pump valve, this article do much basic research work on fracturing pump value. firstly, kinetic characteristics of fracturing pump valve are stated particularly and analysed. through stimulated experiment based on practical working conditions, the wearing disciplinarian and forms of impact particle wear about fracturing pump valve are researched by comparing it with pure impact wear and abrasive wear. furthermore, the wear mechanism of impact particle wear and particle erosion are analysed. in the end, by using the fenite element analyzing tool ansys, the distributing law of stress and strain of fracturing pump valve at the state of closing and during the process of impact are analysed carefully
詳細闡述和分析了它的運動特性;根據其實際工況,通過模擬試驗,研究了壓裂泵閥沖擊磨料磨損的磨損規律和磨損形式,並且將其與純沖擊磨損、滑動磨料磨損進行了對比;分析了壓裂泵閥的沖擊磨料磨損、沖蝕磨損等磨損機理;藉助ansys有限元分析工具,對泵閥關閉狀態下和沖擊過程中的應力應變分佈規律進行了詳細分析。Unlike any other design, the stem head slides inside a circular cavity on the stem guides in the body and bonnet, and is connected to the knife blade by a taper slot
與其它結構不同,這種閥門的閥桿頭部在圓形空腔內滑動,由閥體和閥帽內部引導運動,通過錐形槽連接到閘刀上。Slab type sliding gate valve
平板式滑動閘閥Handwheel torque or actuator force provides positive seat - knife closure. during closure, the stem slides down pushing the knife into contact with the two bottom lugs
手輪扭矩或執行機構扭力是正閥座-閘刀關閉的動力源。在關閉期間,閥桿向下滑動推動閘刀向下抵住兩個底部凸耳。Slide shut - off valve
滑動式截止閥分享友人