滑動電容器 的英文怎麼說

中文拼音 [gǔdòngdiànróngqì]
滑動電容器 英文
sliding capacitor
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 器 : 名詞1. （器具） implement; utensil; ware 2. （器官） organ 3. （度量; 才能） capacity; talent 4. （姓氏） a surname
  • 滑動 : slither; slippage; slipping; slide; sliding; run; sliding movement [motion]; glide; slump滑動閘門...
  • 電容器 : capacitor; condenser; current condenser; electrical condenser
  • 電容 : electric capacity; capacitance; capacity
  1. In the positioning servo - system, which generally is configured by the d. c. pulse width modulator ( pwm ) velocity governing system and position servo - loop, the parameter perturbance of pwm velocity loop really exist by reason of such as the load behavior ; power voltage supply ; operating setting value, etc. 1, 2 ， and it cannot be ignored. by using the identification technique to form the mathematical model of the system, authors have confirmed the facts. therefore, to design the discrete sliding mode controller ( dsmc ) of the positioning servo - system, the perturbed parameters value bounds of the pwm velocity loop, which is as the controlled plant of position servo - loop, should be accounted. consequently, the design principle of dsmc for accounting system with parameter perturbance is proposed by the authors. the proposed method can ensure the stability of system with parameter perturbance and the behavior of non - overshoot, fast precise positioning. in order to reveal the effects of the design method, the comparative research work is done by the authors. also, it has been tested in an industrial experiment, the results proved it is satisfactory

    由直流脈寬調速系統（ pwm ）和位置環構成的定位系統中，速度環的參數隨負載特性；電網電壓；給定工況而攝動是不容忽視的.作者通過系統辨識建模也證實了這一事實1 ， 2 .因此在設計位置環的離散滑模控制時，必須針對速度環（即位置環的控制對象）的參數攝動范圍採用「對象參數攝動離散滑模控制器的設計方法」 ，以確保系統在參數攝動時的穩定性和快速、無超調、準確定位的優良動態品質.為剖析該設計方法的控制效果，本文作了對比性研究，並將該設計方法用於工業試驗中，取得了滿意的結果
  2. In the dissertation, the effects of the air slide - film damping on the capacitive accelerometers having different slot structures which are completely or partly etched, and fabricated by the anodic bonding between silicon and glass and bulk silicon micromachining process are researched by changing the distance between the moving structure and substrate, the thickness of the structure, the width of the completely etched slot structure, the depth of the partly etched slot structure according to the two well known air slide - film damping models

    對于橫向運動的體微機械器件，其周圍空氣表現為滑膜阻尼。本文基於滑膜阻尼的兩個模型，通過改變振子與襯底的間距、振子的厚度、刻透的柵槽的寬度、沒有刻透的柵槽的深度等參數，研究了這些參數對硅?玻璃鍵合工藝製作的體硅微機械電容式傳感器阻尼特性的影響。
  3. Harmonized blank detail specification for lead screw actuated non - wirewound preset potentiometers - square form, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel, rigid terminations - assessment level s

    導螺桿傳動非線繞預調電位器協調空白詳細規范.正方形的容器密閉的與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器剛性終端.評定級別s
  4. Trial - use standard general requirements and test code for dry - type and oil - immersed smoothing reactors for dc power transmission

    Dc動力傳輸的干型和油浸滑式電容器的試驗標準的一般要求和試驗規程
  5. Finally, the paper expatiates the realization process of this design, including the rotation equipment management, the static equipment management, examines and service project management, the electrical management, the meter computer management, the water quality management, the lubricating oil management, the static seal management, the craft pipeline management, the bearing management, the pressure vessel

    最後，文章對系統的設計實現過程進行了闡述，分別對大慶石化總廠設備管理系統的轉動設備管理、靜設備管理、檢維修計劃管理、電氣管理、儀表計算機管理、水質管理、潤滑油管理、靜密封點管理、工藝管線管理、軸承管理、壓力容器管理、安全閥管理進行重點描述。
  6. Detail specification for lead - screw actuated wirewound or non - wirewound preset potentiometers - rectangular and square forms, container sealed, actuating device insulated from resistive element, slipping clutch at each end of travel - full assessment level

    導桿驅動線繞或非線繞預調電位計詳細規范.長方形和正方形密封容器與電阻元件絕緣的驅動裝置每個行程終止的滑動離合器.全面評估級
分享友人
分享到 Line

分享到臉書