滑塊連桿機構 的英文怎麼說

中文拼音 [gǔkuāiliángǎnjīgòu]
滑塊連桿機構 英文
sliding-block linkage
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 桿 : 桿名詞（桿子） pole; staff
  • 機 : machineengine
  • 構 : Ⅰ動詞1 （構造; 組合） construct; form; compose 2 （結成） fabricate; make up 3 （建造; 架屋） bui...
  • 連桿 : [機械工程] link; connecting rod; perch; go between; column; connecting bar; crank guide; link lev...
  • 機構 : 1 [機械工程] （機械的內部構造或一個單元） mechanism 2 （機關; 團體） organ; organization; institu...
  1. Based on above distributed simulation software of multibody system dynamics, three examples of distributed sensibility analysis, double pendulum system, planar four - bar mechanical system and slider - crank system, are numerically dealt with, the results of which indicates that the methods raised in this paper are correct

    基於所完成的系統運動學分散式模擬軟體，實現了雙擺機構、平面四連桿機構、曲柄滑塊機構的分散式靈敏度分析算例，驗證了本文方法的正確性。
  2. In this dissertation, integrated the reduce - vibration project of the engine of the motorcycle company, the eccentricity balance is used in the internal - combustion engine on the basis of analysis of the dynamic balance of the crank - connect rod mechanism for the internal - combustion engine

    本文針對單缸內燃機的曲柄連桿機構的動平衡進行深入分析，在分析的基礎上，針對單缸內燃機的特點進行動平衡設計，提出偏心滑塊機構平衡方法，並針對偏心滑塊機構在生產過程中一些關鍵技術進行分析設計計算。
  3. With different clearance value, displacement curves and velocity curves of generalized coordinates as well as slider displacement error curves in a motion period are obtained. these curves are discussed. results show that if manufacturing cost is kept invariableness, in order to improve precision of mould - cuting, fitting precision of joint connecting the crank and coupler has priority to be considered to increase

    採用四階rong - kuta法求解連續接觸模型的動力學方程，得到了一個運動周期內運動副間隙取不同值時，各廣義坐標的位移、速度曲線和滑塊位移誤差曲線，並通過曲線分析，得出了要提高模切機主切機構精度，在相同加工成本條件下，應優先考慮提高曲柄與連桿鉸接處的配合精度的結論。
  4. In this model, condition is considered for modeling coupler as a rigid rod with two masses at each end

    考慮連桿與滑塊之間的運動副間隙，對主切機構進行三狀態建模。
  5. As a rigid rotor with special configuration, the crank is always integrated with its accessory components such as shaft and piston when it is under working conditions

    曲軸作為結構特殊的剛性轉子，在運行中總是與連桿，滑塊一起構成一個整體的曲柄連桿機構。
分享友人
分享到 Line

分享到臉書