滑環電動機 的英文怎麼說
中文拼音 [gǔhuándiàndòngjī]
滑環電動機
英文
slip ring motor-
Punching tool parts, blocks for edm, scissor parts, circular knives, machine parts, extruding tools, tools for diecasting pulverized materials, pressure plates, sliding parts, valve parts, embossing dies, cutter disks, planer knives for machining of wood, hard metal tipped tools, rolls for cold rolling mills
沖壓工具零件、電火花機床的滑車、剪刀的刃口、環刀、機械零件、擠壓工具、硬模鑄造研磨材料的工具、承壓板、滑動零件、閥門零件、壓花模、圓盤刀、木工中刨刀、切削硬金屬刀片、冷壓滾軸。Pull the slip board, up distance switch to loosen, the film motor starts turn to move after receive the signal, turning to schedule length, pass the sense switch control film electrical engineering automatically stop, put the cup into the bottom slip mold, then push to go into, next circulation beginning
拉出下模滑板，上行程開關松開，膠模電機接到信號后開始轉動，轉過預定長度，通過電眼控制膠膜電機自動停止，將膠杯放入下模滑板，再推入，下一個循環開始。A comparative study and simulation of different control schemes, for the brushless motor variable - speed system, is presented. the simulation results show that, with the outer speed loop based on conventional proportional - integral controller, the dynamic performance of the system is not content, while with intelligence controller, the performance improves, and with variable - structure control with sliding mode, the system response influenced slightly by the vary of the system parameters
本文還對無換向器電動機雙閉環調速系統的不同控制方式進行了模擬比較，結果表明：採用常規的pi轉速調節器，系統的動態性能不是很好；採用簡單的轉速環智能控制器，系統的動態性能能得到一定改善；採用轉速環滑模變結構控制器，系統的響應特性受系統參數變化的影響較小，具有優異的動態性能。A nonlinear speed controller for permanent magnet synchronous motor based on adaptive backstepping control was designed, which uses second - order filter to smooth the speed reference
摘要設計了一種基於自適應同步控制的永滋同步電動機非線性速度控制器，採用二階濾波環節平滑速度指令。On the base of analyzing the work theory of braking system and the ac servocontrol technologies, permanent magnet brush - less motor is used as the electric drive component, the aircraft slippage ratio adjustor and permanent magnet brush - less motor ( pmbm ) speed / current adjuster is made to construct a tri - loop control system
在詳細分析飛機剎車系統的工作原理和交流伺服技術的基礎上，採用稀土永磁無刷方波直流電動機作為驅動部件，飛機期望滑移率控制和電機轉速、電流控制的三環控制方式。Three phase ship - ring motor
三相滑環式電動機Three - phase slip - ring motor
三相滑環式電動機Slip ring motor
滑環式電動機With the aid of these blocks, it is convenient and flexible to make up different kind of automatic - controlled simulating system and so to accomplish different kind of automatic adjusting task. this paper is focused on the construction of the simulation model of ccs by using the contrived control section model. the ccs employs advanced direct energy balance control strategy and can simulate different running patterns such as turbine following boiler pattern, boiler following boiler pattern, etc. two independent control loops : power control and frequency control, are used in the contrivance of deh and they are separately corresponding to the normal condition and the abnormal condition
本文利用開發的控制環節模塊，著重建立了協調控制系統的模擬模型，該協調控制系統採用了先進的直接能量平衡控制策略，並能模擬機跟爐、爐跟機、機爐協調、手動以及定壓和滑壓等運行方式；開發的功頻電液系統模型採用了功率控制和頻率控制兩個獨立的控制迴路，能夠在機組正常運行和啟停時對汽輪機進行控制。Ac slip ring motor
滑環式交流電動機Starter for d. c. - motors and a. c. - slip - ring induction motors
直流電動機和交流滑環感應電動機的起動器Slip - ring induction motor
滑環式感應電動機Slip - ring type induction motor
滑環式感應電動機The table is a important device in the hardware - in - the - loop simulation system, and it simulates the flight of unmanned aerial vehicle so as to achieve flying parameters from those sensors. the signals of sensors in the table are transmitted by many cables previously, thus it confines the movement range of the three - axis frameworks. as the perfomance of uav become complicated, the signals cables are replaced by wire rings in some tables, but it brings many difficulties and unreliable factors for the simulation table ’ s design also. bluetooth, as a new short - range wireless communication technology, is a reasonable and feasible scheme in this condition
三軸模擬轉臺是無人機地面半實物模擬系統中的重要設備，用來模擬飛機在空中的姿態和角運動，以驅動傳感器產生飛行姿態、角速度及角加速度信號。早期轉臺上傳感器信號通過穿在框架中的電纜進行傳輸，這就限制了框架的運動范圍。隨著無人機任務的復雜程度不斷提高，出現了採用導電滑環傳遞信號的模擬轉臺，但這也給轉臺設計帶來了困難，且存在不可靠因素。分享友人