滴水噴嘴 的英文怎麼說

中文拼音 [dīshuǐpēnzuǐ]
滴水噴嘴 英文
drip nozzle
  • 滴 : Ⅰ動詞（液體一點一點地向下落） drip Ⅱ名詞（一點一點地向下落的液體） drop; droplet Ⅲ量詞（用於滴下的液體的數量） drop
  • 水 : 名詞1 （由兩個氫原子和一個氧原子結合而成的液體） water 2 （河流） river 3 （指江、河、湖、海、洋...
  • 噴 : 噴動詞1. （液體等受壓力而射出） spurt; spout; gush; jet 2. （噴灑） spray; sprinkle
  • 嘴 : 名詞1. （口的通稱） mouth 2. （形狀或作用像嘴的東西） anything shaped or functioning like a mouth 3. （指說話） talk; speak
  • 滴水 : 滴水drip滴水管 weep pipe; 滴水培養 drip culture; 滴水器 water-dropper
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. Its atomized parcel is so small that no drip is separated out. this kind of centrifugal nozzle has high humidifying efficiency and low energy cost, which could be used in many situations in textile factories such as directly humidifying in workshop and humidifying in air pipeline

    撞針型高壓小孔徑離心式噴嘴的霧化粒子細小、無水滴析出、加濕效率高、耗能少，可直接向車間加濕，適用於紡織廠等多種應用場合。
  3. The resultant precipitates deposited on pipe walls and in orifices and sprinklers can completely plug the irrigation system

    產生的沉澱沉積于管壁、滴水孔和噴嘴上，完全阻塞整個灌溉系統。
  4. The dehydration time is square of the droplets diameter so the small diameters of the droplets can cut down the drying time then reduce the height of the drying chamber. to the combined spin - flow pressure spray drying, the diameters of droplets are small and the dehydration rate is higher so keeping the qualities of the dried products we can increase the speed of the inlet wind and reduce the temperature of the outlet wind thus can improve the evaporation intensity of the drying chamber and the average energy utilization of the drying equipment

    因霧滴的脫水時間與其直徑的平方成正比，減小液滴直徑有利於縮短乾燥脫水時間，可有效降低乾燥塔的高度；由於旋流式組合壓力噴嘴霧化滴徑的減小，脫水速度明顯加快，在不影響乾燥物料性質的前提下，適當提高進風溫度，同時有效地降低排氣溫度，有利於提高幹燥塔的蒸發強度，也有利於提高幹燥設備的平均能源利用率。
  5. 3. testing all the hydraulic parameters of the sprinkler installed with adjuster such as working pressure, water flux, the range of the sprinkler, intensity of water drop impact, characteristic of water distribution, etc. according to the testing data, we can learn the quantitative relations among the structure of the adjuster, working pressure, diameter of the nozzle, elevation of sprinkler, wind power, velocity of rotation and the range of water

    測試安裝「壓力調節器」后的噴頭的水力性能參數，即工作壓力、流量、射程、水滴的打擊強度、噴灑水分佈特性等。依據所測得的噴頭水力性能參數和射程數據，我們可較清楚的了解「壓力調節器」的結構形式、工作壓力、噴嘴直徑、噴射仰角、風力、旋轉速度和噴頭射程之間的定量關系。
分享友人
分享到 Line

分享到臉書