滾動軸承鋼絲 的英文怎麼說

中文拼音 [gǔndòngzhóuchénggāngsī]
滾動軸承鋼絲 英文
roller bearing wire
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 鋼 : 鋼名詞（鐵和碳的合金） steel
  • 滾動 : roll; trundle; rolling; volution; run; rolling motion滾動半徑 rolling radius; 滾動傳感器 roll sen...
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  • 鋼絲 : steel wire; wire; wire-steel
  1. In the interest of adapting big size in radial direction, higher precision, higher angular rigidity, less moment of inertia, higher dynamic capability in the three - anxis simulation test turntable. researching the angular rigidity of the wire race ball bearings in axes direction, the adjustment mode and adjustment quantity to shafting, and analysing the contact stress of bearings in work is very necessity

    為了適應某些模擬轉臺研製中關于剛度高，轉動慣量盡量小，動態特性要求高等特殊要求，研究鋼絲滾道球軸承的軸向支撐剛度，軸系調整方式及調整量，以及該軸承在工作中的受力及應力狀況十分必要。
  2. This paper first conducts the research to the steel wire roller conveyer ball bearing rolling body and the steel wire roller conveyer spot contact question, gives the main geometry parameter of the zone of contact by the hertz contact theory, stress extreme value as well as contact body elasticity approach quantity formula, and acts according to the practical application to carry on the simplification, calculates the main parameter of the bearing zone

    本論文首先對鋼絲滾道球軸承滾動體與鋼絲滾道的點接觸問題進行研究，由hertz接觸理論給出接觸區的主要幾何參數，應力極值以及接觸體彈性趨近量的計算公式，並根據實際應用進行簡化，計算出課題所研究軸承接觸區的主要參數。
  3. Fork - ends, in corrosion - resistant steel, threaded, for rolling bearings, for aircraft control wire rope - dimensions and loads

    航空器操縱鋼絲繩用滾動軸承的螺紋式鋼制叉形端.尺寸及載荷
  4. Possessed more light mass, much less inertia, small size in axes direction, big size in radial direction, higher angular rigidity, frequently been of use in shafting of big radius

    鋼絲滾道球軸承具有重量輕，轉動慣量低，軸向尺寸小，徑向尺寸大，支撐剛度高等特點，常用於支撐大口徑中空軸系。
  5. Aerospace - fork - ends, in corrosion - resistant steel, swaged on aircraft control wire rope, for rolling bearings - dimensions and loads

    航空航天.航空器滾動軸承操縱鋼絲繩上的鍛制耐腐蝕鋼制叉形端.尺寸及載荷
分享友人
分享到 Line

分享到臉書