滾齒過程 的英文怎麼說

中文拼音 [gǔnchǐguòchéng]
滾齒過程 英文
hobbing process
  • 滾 : Ⅰ動詞1 （翻轉; 滾動） roll; turn round; trundle 2 （走開; 離開） get away; beat it 3 （液體沸騰）...
  • 齒 : Ⅰ名詞1 （牙; 牙齒） tooth 2 （物體上齒形的部分） a tooth like part of anything 3 [書面語] （年齡...
  • 過 : 過Ⅰ動詞[口語] （超越） go beyond the limit; undue; excessiveⅡ名詞（姓氏） a surname
  • 程 : 名詞1 （規章; 法式） rule; regulation 2 （進度; 程序） order; procedure 3 （路途; 一段路） journe...
  • 過程 : process; procedure; transversion; plication; course
  1. This paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surfaces characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  2. Abstract : this paper puts out the edge shapes curvilinear equations, of the edge shapes of double circular gear hob, and analyzes the tooth surface ' s characterist. it also points out that the gear hob is a kind of approximate shape building cutting too ls in the whole course of using

    文摘:本文提出了直槽雙圓弧齒輪滾刀刃形曲線方程式，並進一步分析了該滾刀的齒面特性，指出該滾刀從整個使用過程看，是一種近似造型的刀具。
  3. Established the system of coordinates of roll testing, getting the parameters of equation of tooth face by solving the non - linear equations set ; according to the differential geometry and meshing principle, deduce the curvature parameters of tooth face and tooth profile, and get the parameters of instantaneous contact ellipse. emulate the contact trace and contact area of the working tooth face, and drawing the instantaneous drive ratio error curve

    建立了克林貝格擺線齒錐齒輪嚙合分析的對滾模型，通過對非線性方程組的迭代求解，得到齒面方程的各個參數;由微分幾何和切齒嚙合原理推導了齒面上齒廓和齒線方向的曲率參數，得到了瞬時接觸橢圓的參數。根據設計參數和機床調整參數繪制了工作齒面的接觸軌跡和接觸區圖形，並求得了瞬時傳動比的誤差曲線。
  4. The wastage morphology and reasons of gear hob used in production are analyzed, the influence of the varying hobbing torque and temperature on wastage of hob is discussed in hobbing process

    摘要對生產中使用的齒輪滾刀磨損和破損形貌進行了分析，探討了滾刀磨損和破損的原因及滾齒過程中滾削力和滾削溫度的變化對滾刀磨損和破損的影響。
  5. The situation and development of domestic and foreign manufacture, especially in the europe, america and asia, have been summarized and researched in the article, so the following work has been finished, and the conclusions and results are obtained as follows : through analyzing the features of movement, power and construction for the high - speed cnc gear hobbing machine in 6 - axis with four coordinated, the design methods of general arrangement, kinetics and kinematics are put forward. 1. by analyzing the severe challenge to the machine manufacture in the market, developing and managing methods of serial modular products are posed

    為了給我國汽車工業和其它行業提供先進的齒輪加工設備，本文在總結、研究國內外特別是歐美國家齒輪機床現狀與發展的基礎上，進行了以下研究工作，並得出相應的結論與成果：分析了六軸四聯動數控高速滾齒機的運動、動力、結構特點，提出了六軸四聯動數控高速滾齒機的總體布局設計、動力設計、運動學設計方法；分析並根據市場對機床製造業提出的嚴峻挑戰，提出了數控滾齒機系列產品的模塊化開發方法與管理方法；在分析了六軸四聯動數控高速滾齒機模塊化設計的技術先進性與經濟性間辨證關系的基礎上，提出了產品開發過程中以邊際成本法進行經濟分析的方法。
  6. By means of the optimization method - punishing function method and taking the sum of the planet gear radius and center distance as the target function, the parameters of drive are optimized. by using the optimization program, the initial serial studies of drive are completed, the best serial parameter value of the drive is given

    採用外點罰函數優化方法，通過取行星輪半徑和中心距之和作為優化目標函數，對滾錐齒超環面行星蝸桿傳動進行了參數優化，運用此優化程序，初步完成了對該種傳動的系列化研究，給出了傳動系列的最佳參數取值。
  7. 3, during the process of the gear teeth meshing, the film shape and pressure distribution have little difference. but, the temperatures have the distinctive changes as the engaged position is varied, which means that the temperatures as the increase in the rate of slide to roll

    3 、在齒輪傳動嚙合過程中，壓力分佈和油膜形狀無明顯變化，但溫升隨嚙合位置的不同呈顯著變化，即溫升隨著滑滾比增大而增大;在單、雙齒嚙合交替處，摩擦系數達到極值，可達0 . 08 。
  8. The paper has begun with existing driving mechanism of horizontal barrel finishing equipment and analysed the reason that creates the family of crank parts machining quality problem. the transmission plan of noncircular gears connect crank - slider mechanism has been presented and mathematical model of driving mechanism has been established. by way of programming operation, simulation analysis and parameter optimization, the feasibility of new plan has been proofed

    本課題從現有臥式滾磨設備的傳動機構入手，對造成曲軸類零件加工質量問題的原因進行了分析，提出引入非圓齒輪串聯曲柄滑塊機構的傳動方案，建立了傳動機構的數學模型，通過計算機編程運算及模擬分析和參數優化，驗證了所提新方案是可行的。
  9. Gear form is precisely, plotted by portray point. for friendly user interface, the dialog - box is given, using dcl language to compile dialog box program. because the given program can not only output all the optimum basic parameters of pump gear, but also simulate the meshing process of a pair of pump gears, gear pump can be designed and manufactured economically

    精確繪出泵齒輪的輪齒幾何形狀，尤其精確繪制出了標準齒輪滾刀切出的齒根過渡曲線，演示了國標雙圓弧頭標準滾刀加工泵齒輪的過程，並實現了泵齒輪副的嚙合模擬，這些對檢查輪齒干涉以及確定齒輪泵的卸荷槽位置和形狀提供了依據。
  10. The key factor influencing the automobile ' s drive bridge performance is the reducer assembly quality, and the tightening at the bearing of the front - part of the driving gear axis is an important problem in the process of the reducer assembly

    汽車驅動橋主減速器的裝配質量是影響驅動橋整體性能的一個關鍵因素，主減速器裝配過程中的一個重要問題就是主動錐齒輪前端的一對圓錐滾子軸承的預緊。
分享友人
分享到 Line

分享到臉書