潤滑油泵軸承 的英文怎麼說

中文拼音 [rùngǔyóubèngzhóuchéng]
潤滑油泵軸承 英文
bearing for lubricating pump
  • 潤 : Ⅰ形容詞（細膩光滑; 滋潤） moist; smooth; sleek Ⅱ動詞1 （加油或水 使不幹枯） moisten; lubricate 2 ...
  • 滑 : Ⅰ形容詞1 （光滑; 滑溜） slippery; smooth 2 （油滑; 狡詐） cunning; crafty; slippery Ⅱ動詞（貼著物...
  • 油 : Ⅰ名詞1 （脂肪; 油脂） oil; fat; grease 2 （姓氏） a surname Ⅱ動詞1 （用桐油、油漆等塗抹） apply t...
  • 泵 : 名詞（吸入和排出流體的機械） pump
  • 軸 : 軸Ⅰ名詞1. （圓柱形的零件） axle; shaft 2. （對稱部分的直線） axis 3. （圓柱形的纏繞器物） roller; spool Ⅱ量詞（用於纏在軸上的線以及裝裱帶軸子的字畫）
  • 承 : Ⅰ動詞1 （托著; 接著） bear; hold; carry 2 （承擔） undertake; contract （to do a job） 3 （客套話...
  • 潤滑油 : lube; lubricating oil; lubricant oil; lubrication oil; lube oil
  • 潤滑 : [機械工程] lubricating; lubrication; lubricate
  • 軸承 : [機械工程] bearing; axle bearing; bearing of shafts; gudgeon block; mechanical bearing; pillow; s...
  1. Lqry series hot oil pump is supported by the ball bearings at the both ends, front end lubricated by lubricating oil, while back end lubricated by grease, with an oil conduit in the middle used to observe the conditions of sealing and recovery of heat conduction oil

    Lqry系列熱油泵的支撐採用了雙端球軸承支撐的結構形式，前端採用潤滑油潤滑，後端採用潤滑脂潤滑，中間有一導油管，用以隨時觀察密封情況和回收導熱油。
  2. Through the statistic analysis on the change of the melt gear pump working condition pre - and post - pet plant capacity increasing and concatenate direct spinning process, the reasons for the unsteady running were studied, the modification measures such as lubricating the oil groove with sliding bearing, mechanical sealing of the gear pump, decreasing the gear pump outlet pressure, changing the automatic speed increasing to hand speed increasing were put forward

    摘要通過對聚酯裝置增容和後接直紡長絲前後熔體齒輪泵工況變化的統計分析，研究其運行不穩定的原因，提出改造措施，包括滑動軸承潤滑油槽，齒輪泵的機械密封，降低齒輪泵出口壓力，改自動提速為手動提速等等。
  3. The mainly works had been done as follows : 1. in order to keep commonality, the modules who have similar thermodynamic process had been classed. such as evaporating module ( including furnace, drum, system of boiler recycled water ), single - phase heat exchange module ( including superheater, reheater, ecomomizer ), lubricating oil system module ( can be used for any lubricating oil system of rotation mechanical impedance ), pump and fan module, ect

    本文所作的主要工作如下: 1 、為保證模塊的通用性，對鍋爐有相似熱力環節的模塊進行分類，建立模塊庫，便於模塊調用，如蒸發區模塊（包括爐膛、汽包和爐水循環系統） ，單相換熱模塊（包括過熱器，再熱器，省煤器等） ，潤滑油系統模塊（可用於各種轉機軸承潤滑油的動態特性的計算） ，泵與風機的動態計算模塊等。
  4. Bearing oil pump

    軸承潤滑油泵
分享友人
分享到 Line

分享到臉書