澆注塊 的英文怎麼說

中文拼音 [jiāozhùkuāi]
澆注塊 英文
castable
  • 澆 : 澆名詞（姓氏） a surname
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 塊 : 名詞（古時佩帶的玉器） penannular jade ring （worn as an ornament in ancient china）
  1. Square slabs were cut from cubes cast with various aggregate sizes.

    從具有不同骨料粒度的立方澆注塊中切出方形板塊。
  2. The word "grain" is an old ordnance term for explosive powder or even for blocks of cast powders or crystals.

    藥柱這個詞是用於炸藥或者甚至用於澆注火藥塊或晶體塊的一個古老的軍械術語。
  3. The design and machining technology process of its molding part including the front moulding plate 、 front mould kernel 、 back mould plate 、 back mould kernel 、 back mould set piece 、 incline guide pin 、 slide steatite etc, and the choice and calculation of technology parameters of the impotent part, the design process of extrusion outfit, inject system and other makeup are specified in detail ; test and product have been introduced

    詳細地敘述了模具成型零件包括前模板、前模仁、后模板、后模仁、后模鑲件、斜導柱、滑塊等的設計與加工工藝過程，重要零件的工藝參數的選擇與計算，推出機構與澆注系統以及其它結構的設計過程，並對試模與產品缺陷作了介紹。
  4. The composite material, which is used to make muller plow of sand mill, is prepared by the method of cast - infiltration and the technology parameters for making composite material is optimized. then the effects of the matrix component on composite layer also are disccused

    通過試驗對利用鑄滲法在鑄件表面獲得一定厚度復合材料層的形成機理進行了理論分析，優選了利用鑄滲法在鑄件表面制備復合材料的工藝參數（澆注溫度、合金膏塊的厚度、澆注位置等） 。
  5. It is necessary coal dust to inspect and evaluate comprehensively all physical - chemical properties of the coal dust, as well as to determine its anti - metal penetration ability by pouring a test specimen

    選擇煤粉應通過全面的檢測和評價各項理化指標，並通過試塊澆注試驗以確定其防粘砂能力。
  6. The speed became fast at the temperature 1050. the reaction could carry completely when billets was kept in vacuum tube for 3 hours " at 1050 temperature, under the striking of great quantity of heat when the molten iron poured into the mold, the reaction was blazed rapidly and continued at a high speed. the diffusible speed of v and c was very fast because the billet was heated over 1300 in a moment, so the reaction ca n complete in a few minutes

    （ 5 ）碳化反應v + c vc在900左右開始發生，此時是固相反應，反應速度較慢，反應不能進行完全，隨溫度升高，該碳化反應的速度加快，在1050保溫3小時可以進行完全，在鑄造燒結時在過熱鐵水的巨大熱流密度沖擊下， v + c vc立即被激發，並以很快的速度進行，由於坯塊被加熱到1300以上，此時c和v擴散速度很快，因此鑄造澆注后的幾四川大學碩士學位論文分鐘內反應可以進行完全。
分享友人
分享到 Line

分享到臉書