澆注系數 的英文怎麼說

中文拼音 [jiāozhùxìshǔ]
澆注系數 英文
gating system
  • 澆 : 澆名詞（姓氏） a surname
  • 注 : Ⅰ動詞1 （灌入） pour; irrigate 2 （集中） concentrate on; fix on; focus on 3 （用文字來解釋字句）...
  • 系 : 系動詞（打結; 扣） tie; fasten; do up; button up
  • 數 : 數副詞（屢次） frequently; repeatedly
  • 系數 : [數學] coefficient; ratio; modulus; quotient; factor
  1. The design and machining technology process of its molding part including the front moulding plate 、 front mould kernel 、 back mould plate 、 back mould kernel 、 back mould set piece 、 incline guide pin 、 slide steatite etc, and the choice and calculation of technology parameters of the impotent part, the design process of extrusion outfit, inject system and other makeup are specified in detail ; test and product have been introduced

    詳細地敘述了模具成型零件包括前模板、前模仁、后模板、后模仁、后模鑲件、斜導柱、滑塊等的設計與加工工藝過程，重要零件的工藝參數的選擇與計算，推出機構與澆注系統以及其它結構的設計過程，並對試模與產品缺陷作了介紹。
  2. The influences of foundry process and method factors on combination effect was investigated including the influences of gating system design, pouring temperature, atmospheric pressure of mould cavity, thickness of cast - penetrated layer and so on

    作者就澆注系統、澆注溫度、型腔氣壓、鑄滲層厚度等工藝參數對鑄滲效果的影響進行了試驗研究。
  3. The research showed that basin is the more important feeding resource than runner in runner type gating system in lost wax casting. therefore, on the basis of the basin as feeding resource, runner and ingate as feeding channel, a new design method for runner type pouring and feeding system in investment casting was developed. the corresponding feeding mathematical pattern and allowable total weight listed for casting cluster with different basin were established after analyzing the practical feeding of basin and the calculating process for design was described in detail

    在熔模鑄造橫澆道型澆注系統中，澆口杯是比橫澆道更為重要的補縮源，因此在立足於澆口杯為補縮源、橫澆道和內澆道為澆注補縮通道的基礎上，開發了適用於熔模鑄造橫澆道型澆注補縮系統設計的新設計方法，在詳細分析了澆口杯的實際補縮情況后，建立了相應的數學補縮模式和不同澆口杯的鑄件組許用鑄件總質量表，並具體介紹了設計計算過程。
  4. The sensitivity algorithm is a knowledge of research on the affection of parameters varies to system performance. combination with pressing force and infuse time predicted model, by using sensitivity algorithm, the affection of cast temperature, mould temperature and infuse pressure on infuse time is researched deeply, and the affection of cast temperature, infuse time and infuse pressure on the pressing force in the origination stage of extrusion process. the sensitivity analysis has huge instructing significance to the selection of parameters

    靈敏度演算法是分析參數變化對系統性能影響的一種有效工具，所以本文引入靈敏度演算法，結合壓制力和浸滲時間預測模型，深入研究了澆注溫度、模具溫度和浸滲壓力對浸滲時間的影響關系，以及澆注溫度、模具溫度、浸滲時間和浸滲壓力對擠壓過程起始階段壓制力的影響，對于參數的選取，具有一定的指導意義。
  5. We are manufacturer and exporter of laser printer copier accessories, the primary products are fuser film sleeve, pcr, cleaning web roller, blade etc. our products are sold very well in many countries because of the high quality and reasonable price. all the materials are imported from japan. the quality can match oem

    主要經營的產品有進口的hp全系列定影膜hp1000 1010 5l 2200 4000 5000 5100等等，以及canon數碼復印機定影膜ir3300 2800 2200 fc290 280 200和canon - gp215數碼復印機定影膜充電輥印表機復印機清潔刮板印表機復印機搓紙輪充電膜套擋粉片粉瓶燈管等五十多種oa耗材配件以及裝粉機離心機精密擠出設備吹瓶設備精密澆注機搓紙輪專用設備等。
  6. The polyacrylonitrile have no use to improve the homogeneity of concrete. the homogeneity of concrete have bad effect to compression strength, but the effect to chloride ion coefficient of diffusion is not obvious. for concrete used generality, if it ’ s homogeneity is acceptable ( k 7 % ), the percentage of lost of the compression strength will lower than 10 %

    勻質性對抗壓強度的影響較大，對氯離子滲透系數的影響不明顯，對於一般用途的混凝土，勻質性良好（ k 4 % ）時，強度損失在5 %以內，勻質性合格（ k 7 % ）時，強度損失在10 %以內;對于深層澆注的混凝土，離析度k 3 %時上下層強度的差異率才能保證在5 %以內。
  7. Model jy light thermal insulating pouring material is new irregularly setting fire - resistant material which is made from the excellent and super powerful light aggregate, super minunt material, combine agent and additional agent. this material is series of new fire - resistant lining naterial with low density, high intensity, small thermal conductivity

    Jy系列輕質保溫澆注料是一種新型不定型耐火材料，由優質超強輕質骨料、超細粉、結合劑和外加劑組成，是一系列密度低、強度高、導熱系數小的新型隔熱襯里材料。
  8. By close study on the average temperature rise, temperature distribution, and tune constant of the class f resin dry type power transformer ' s high voltage and low voltage winding under self - cooling and wind - cooling mode, we find out the connection between the variation of the load and the items, mentioned above. the results of the experiments can be reference to both thermal design optimization of dry type power transformer and the revision of current standards. meanwhile, we develop the software, which can predict the overload ability of the dry type power transformer

    本文對f級樹脂澆注式乾式變壓器的高、低線圈的平均溫升，內部溫度分佈和時間常數在自冷和風冷，兩種冷卻方式下隨負載變化的規律進行了研究，得出了平均溫升、熱點溫升和時間常數隨負載變化的相互關系和有關計算用參數和公式，試驗結果可作為改進乾式電力變壓器的熱設計的依據和對現行標準進行修改的參考。
  9. The high voltage windings is made by sectional aluminium foil with glass fiber and resin casting, the voltage between turns is very low, the partial discharge is very low, there is no cracking, since the expansion factor of conductor and insulation material is similar, it also has the advantages of no corrosion, no pollution, low losses, low noise level, anti - vibration, fire protection, maintenance free, long operating life and high reliability

    低壓繞組為銅箔繞制，半干nomex紙做層間和外層絕緣，經乾燥與銅箔固化為一體，散熱好強度高。高壓繞組為分段鋁箔繞制，玻璃絲網架環氧樹脂澆注，層間電壓低，局部放電小，導體和絕緣體膨脹系數相似，不裂壽命長無腐蝕無污染損耗小噪音低抗震阻燃免維護運行安全可靠。
  10. Qj series amorphous refractory developed by this factory is series insulation castable, which has such advantages as high refractoriness, high crushing strength and small thermal conductivity. this series product is used widely as insultion material for various heating furnace, atmospheric and vacuum furnace and sulfur recovery device in petrocnemical industry

    Qj系列不定形耐火材料是我廠自行研製的系列保溫隔熱澆注料，它具有耐火度高，耐壓強度高，導熱系數小等特點，該系列產品廣泛應用於石油化工各類加熱爐，常減壓爐，硫回收裝置等工業窯爐作保溫熱材料。
  11. Abstract : based on the methods of the fuzzy theory, a mathematics model of fuzzy comprehensive evaluation for the problems of unbalanced flowing system of multi - cavity injection mold, have been established. fuzzy comprehensive evaluation of different processing conditions are made by the proposal method

    文摘:根據模糊論方法的原理，針對一模多腔非平衡布置的澆注系統的流動平衡問題，建立了模糊綜合評判的數學模型，完成了多種成型工藝方案的模糊評判。
  12. In this paper, mould cad technique is studied, artificial intelligence technique is introduced and expert system design method is used. with object - oriented technique, database technique, fuzzy theory and computer image technique, second development of autocad 2002 is carried on and a common injection molding runner system based on intelligent object and fuzzy reasoning is designed and implemented

    本文在研究注塑模cad技術的基礎上，通過引入人工智慧技術，採用專家系統的設計方法，綜合運用面向對象技術、數據庫技術、模糊理論和計算機圖形技術對autocad2002進行二次開發，設計實現一個基於智能對象和模糊推理的注塑模普通澆注系統。
  13. The functions of the system involve process parameters design, sand core design, riser design, gating system design, pattern plate design, core box design, and creation of two - dimensional drawings and charts

    該系統針對汽車鑄件，其功能包括工藝參數設計、砂芯設計、冒口設計、澆注系統設計、模板設計、芯盒設計以及二維工藝圖、卡的生成。
  14. Light quality indefinite type pour material is it insulate against heat of good performance to have, heat conduction coefficient little, energy - conserving result remarkable, the intensity is high, the line changes littly, various kinds of stove kiln ideal inside lining, adiabatic material, please according to select different materials for use while being different kinds of, it is easy to economize the kiln cost

    輕質不定型澆注料具有隔熱性能好、導熱系數小、節能效果顯著、強度高、線變化小，各種爐窯理想的內襯、絕熱材料，請按不同類型選用不同材質，便於節約窯爐成本。
分享友人
分享到 Line

分享到臉書