澆鑄溫度 的英文怎麼說
中文拼音 [jiāozhùwēndù]
澆鑄溫度
英文
cast temperature-
Scrap steel will be loaded into steelmaking furnace and molten after sieving and dewetting. if the chemical composition and target temperature of molten steel are satisfied, the molten steel will be poured into ladle and conveyed to continuous caster, then be made as billet with specified length
廢鋼鐵經篩選去濕，裝入煉鋼爐冶煉融化成鋼水，當達到要求的化學成分及溫度目標值時，將鋼水倒入鋼水包，送至連鑄機，澆鑄成定尺長度的鋼坯The results show that the heat preservation coating and its proper thickness are favorable to the enhancement of filling mold speed of aluminium alloy ; the higher the pouring temperature is and the larger the ratio of hollow areas of vertical pouring is, the faster the speed of filling mold of aluminium alloy is ; if the mold is too thick or too thin, it may decrease the speed of filling mold ; the proper length and the area of vertical pouring are favorable to the enhancement of the speed of filling mold ; although negatire - pressure may improve filling the speed, too high negatire - pressure may enlarge the flaw in casting
結果表明：保溫塗料及一定的塗層厚度有利於提高鋁液的充型速度；澆注溫度越高、直澆道空心面積率越大，鋁液充型速度越快；模樣厚度太厚或太薄，均會使鋁液充型速度降低；一定的直澆道長度及直澆道面積有利於提高鋁液的充型速度；施加負壓會使鋁液的充型速度大大提高，但負壓過大會增大鑄造缺陷。The influences of foundry process and method factors on combination effect was investigated including the influences of gating system design, pouring temperature, atmospheric pressure of mould cavity, thickness of cast - penetrated layer and so on
作者就澆注系統、澆注溫度、型腔氣壓、鑄滲層厚度等工藝參數對鑄滲效果的影響進行了試驗研究。The effect of compound casting technology and compound modification on the properties of high speed steel roll collar was studied. the results showed that compound high speed steel roll collar with high and even hardness and good bond between outer and inner layers could be gained when the modified colbalt free high speed steel in outer layer and nodular iron inner layer in connection with appropriate rotational speed of centrifugal machine, pertinent pouring interval between two kinds of the melt and moderate pouring temperature as well as surface induction heat treatment were chosen. it is indicated in industrial use that the service life of compound roll collar is higher by 5 times than that of high chromium cast iron collar
研究了離心復合鑄造工藝和復合變質處理對高速鋼輥環性能的影響，結果表明，選用變質高碳無鈷高速鋼作外層，用球鐵作內層，選擇合適的離心機轉速、兩種金屬熔液澆注間隔時間和澆注溫度，結合採用表面感應熱處理工藝，可獲得硬度高、均勻性好、內外層結合良好的高速鋼復合輥環，用於工業生產其使用壽命比高鉻鑄鐵輥環提高5倍以上。Pouring temperature is the dominating factor for the properties of compositing layers
澆注溫度是影響鑄滲表面復合層質量的最主要因素。The effective cost dust content of molding sand should be determined according to time factors such as the quality of the coal dust, casting size and thickness, pouring temperature, lacing sand or unit sand, and so on
決定型砂中的有效煤粉含量應根據煤粉質量的優劣、鑄件大小和厚薄，澆注溫度、面砂或單一砂等因素。Based on the mechanism of hot cracking formation of castings, the cracking defects of furnace door frame castings was analyzed, and found that the main reasons causing cracking are as follows : construction of the casting was not reasonable, gating system was not proper, and pouring temperature was too high
摘要根據鑄件產生熱裂紋的機理，對爐門框裂紋缺陷進行分析，找到了裂紋產生的主要原因是鑄件結構和澆注系統不合理，以及澆注溫度過高。According to simulation results we decide the location of parting face and cooling system 、 the shape and location of runner and gating system etc. after that we take the az91d magnesium alloy shell of motorcycle engine as an example to proceed fine factors ( plunger injection speed 、 pouring
然後以az91d鎂合金摩托車發動機外殼為例，進行五因素（壓射速度、澆注溫度、鍛造時間、壓射比壓、鍛造壓力）四水平l16 （ 45 ）正交實驗，在普通壓鑄過程中關閉鍛造功能。The composite material, which is used to make muller plow of sand mill, is prepared by the method of cast - infiltration and the technology parameters for making composite material is optimized. then the effects of the matrix component on composite layer also are disccused
通過試驗對利用鑄滲法在鑄件表面獲得一定厚度復合材料層的形成機理進行了理論分析，優選了利用鑄滲法在鑄件表面制備復合材料的工藝參數（澆注溫度、合金膏塊的厚度、澆注位置等） 。The alloy component and the process parameters of the precision casting ( including the exit temperature from furnace, pouring temperature, mould preheating temperature, holding time, cooling form ) have a certain influence on the problem of the blade brittles
摘要合金含量、精鑄工藝參數（出爐溫度、澆鑄溫度、模殼預熱溫度、保溫時間、冷卻方式）對葉片脆性問題存在一定的影響。There are five parameters need to be measured. there are five channels for input : the displacement of casting - roller, the rotate speed of casting - roller, the pressure of casting and rolling, the casting temperature and the water - speed of cooling water. they are measured by raster, photoelectric coder, strain pressure sensor, thermocouple and turboflowmeter
系統需要進行監測的參數有五個，即有五路輸入信號：鑄輥位移、鑄輥轉速、鑄軋壓力、澆鑄溫度、冷卻水流速，分別採用光柵、光電編碼器、應變式壓力傳感器、熱電偶和渦輪流量計作為檢測元件。The reason of misrun and cold - lap formation in thin - walled aluminum casting is analyzed. increasing gas exhaust capacity in mould and filling velocity and controlling melt temperature are favorable methods for better effect
對薄壁鑄鋁件澆不足及冷隔的形成原因進行了分析，提出了增大鑄型排氣性、提高充型速度、控制出爐溫度的解決措施，效果良好。The performance consistence of ab5 alloy in mass production is influenced by not only the quenching condition, but also the impurities such as fe, mg in mischmetal and the melting technology including the unit output, melting temperature and time, atmosphere, furnace frequency etc
合金性能波動除受澆鑄時的冷卻條件影響外，還與稀土原料中鐵、鎂等雜質及熔煉工藝因素（包括單位產量、熔煉溫度、時間氣氛及爐頻等因素）有關。The speed became fast at the temperature 1050. the reaction could carry completely when billets was kept in vacuum tube for 3 hours " at 1050 temperature, under the striking of great quantity of heat when the molten iron poured into the mold, the reaction was blazed rapidly and continued at a high speed. the diffusible speed of v and c was very fast because the billet was heated over 1300 in a moment, so the reaction ca n complete in a few minutes
（ 5 ）碳化反應v + c vc在900左右開始發生，此時是固相反應，反應速度較慢，反應不能進行完全，隨溫度升高，該碳化反應的速度加快，在1050保溫3小時可以進行完全，在鑄造燒結時在過熱鐵水的巨大熱流密度沖擊下， v + c vc立即被激發，並以很快的速度進行，由於坯塊被加熱到1300以上，此時c和v擴散速度很快，因此鑄造澆注后的幾四川大學碩士學位論文分鐘內反應可以進行完全。分享友人