火花隙 的英文怎麼說
中文拼音 [huǒhuāxì]
火花隙
英文
air gap-
Study on volt - ampere properties in wedm
電火花線切割加工中放電間隙伏安特性的研究Detonation is a secondary explosion that occurs in the combustion chamber after the spark jumps the sparkplug gap.
爆震是在燃燒室內當火花跳過火花塞電極間隙以後發生的一種二次爆燃。Nowadays, the switches which are being studied or applied, such as gas spark gap, thyratron and ignitron, etc, are of different structures, operating principles, advantages and disadvantages, and are applied in various situations and fields
目前處于試驗中或者投入實際應用的開關元件很多，如火花放電間隙、閘流管、引燃管等，它們有不同的結構、原理和優缺點，應用在不同的場合和領域。Incondition of surface anti - corrision and insulation coat of metal and tiny hole of steel where resistance and crack is very small, when supplying a high voltage, gas crack will be punctured and electric spark discharging will occur, now send a pulse signal to the alarming circuit the alarmer can send out sound and light to alarm. we can do leak hunting on the coating according to this principle
金屬表面絕緣防腐層過薄、漏鐵及漏電微孔處的電阻值和氣隙密度都很小，當有高壓經過時就形成氣隙擊穿而產生火花放電，給報警電路產生一個脈沖信號，報警器發出聲光報警，根據這一原理達到防腐層檢漏目的。Inductive resistance current limiter is comprised of series reactor with lower reactance, damping resistor and sparkle gap
電感電阻型限流器由電抗值較小的串聯電抗器阻尼電阻器和火花間隙等三部分組成。Triggered spark gap
觸發火花隙觸發放電器Untriggered spark gap
非觸發式火花隙Transformers and reactors - part 14 : external protective spark gaps on bushings
變壓器與電抗器.第14部分:套管的外部保護火花間隙Safety spark gap
安全火花間隙The french lightning protection association cautions against the use of spark gap protectors in most applications
法國雷擊防護協會提醒在大部分場合謹慎使用火花間隙保護器。By using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache
通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。Abstract : by using a counter and an operation microprocessor, this paper analyses the measuring method and designs an instrument of edm sinking process in discharge state. this instrument takes samples of voltage, current signal and strong and weak of high frequency signals of detecting voltage amplitude, translates them into various time pulses in discharging state. and a counting unit turns these pulses into digital signals, then send them to a microprocessor. finally various discharge time percentages are sent to the control tache
文摘:通過采樣電火花加工放電間隙的電壓、電流信號和檢測電壓幅值上的高頻信號的強弱，得出反映間隙放電狀態的各種時間脈沖，利用計數器分別對其計數，再送給單片機運算處理，輸出控制環節所需的各種放電狀態時間百分數。According to the state of discharge gap, combining database technology, we adopt neuro - fuzzy control technology to realize real - time control of edm process and auto - adjustment on the basis of process state, which ensure the process is in the state of optimization
依據放電間隙狀況，通過採用神經模糊控制智能技術，並結合數據庫技術，對電火花成型加工過程進行實時控制，根據加工狀態自動進行調節，保證了加工過程處于優化狀態。Abstract : on the basis of that the proportion of time spent sparking is analyzed in electrical discharge machining ( edm ) process, a new method. which is used to ascertain the trend of discharge gap change, is presented. and a fuzzy control strtegy is introduced to parctical use, the results is well
文摘:通過對電火花成形機放電狀態的分析，提出了利用分析周期內出現異常放電狀態時間的比例及開路狀態所佔時間的比例，來判別電火花成形加工的間隙放電狀態及其變化趨勢的方法，並在此基礎上利用模糊控制策略實現了對電火花成形加工過程中放電狀態的控制，取得了令人滿意的效果。He produced an electric spark across a gap between two metal balls by applying an electric current to them.
他把電流接通到兩個金屬球上而在其間的間隙處產生火花。Surface gap spark plug
沿面間隙火花塞The results of calculations and experiments show that the delay and jitter increased as the percentage of sf _ ( 6 ) in sf _ ( 6 ) - n2 mixtures increased. the results of experiments show that the delay of sf _ ( 6 ) - ar follows the same rule. the u _ ( th ) u _ ( sb ) increased as the percentage of sf _ ( 6 ) in sf _ ( 6 ) - n _ ( 2 ) mixtures increased
B ：等u _ w條件下電脈沖觸發火花隙的觸發延遲時間（ t _ d ）及其抖動（ t _ j ）隨混合氣中sf _ 6含量上升而上升，且場利用系數對這一規律沒有影響。The falling rate of t _ ( d - ) p curve closely related with e / p or the energy of laser pulse ( e _ ( laser ) tested. the threshold voltage did n ' t depend on the pressure apparently. the delay and jitter decreased exponentially as the e _ ( laser ) increased
C :建立了零維「 2光子激發一2光子電離」激光觸發火花隙數值模擬模型與考慮了levison修正的t . h . martin經驗公式相結合的激光觸發多級開關零維數值計算模型。A 200kv laser triggered multi - stage multi - channel switch, a 200kv / 100ka multi - channel ring rail electrode field distortion switch and a 5mv laser triggered multi - stage multi - channel switch were designed and tested. the main results and conclusions of this dissertation are as follows : ( 1 ) the switching property of sf _ ( 6 ) - n _ ( 2 ), sf _ ( 6 ) - ar mixtures and the design techniques of multi - channel field distortion switch were studied. a 0 - demension " 2 - 2 " model was developed to study the interaction of the uv laser with sfe gas and sf _ ( 6 ) - n _ ( 2 ) mixtures
本論文研究了激光觸發多級多通道開關的運行機理、 sf _ 6 n _ 2 、 sf _ 6 ar混合氣的開關特性和多通道場畸變開關設計技術，建立了零維激光觸發火花隙及激光觸發多級多通道開關數值模擬模型，研製了200kv原理型激光觸發多級多通道開關、 200kv 100ka環軌式場畸變開關和5mv激光觸發多級多通道開關，獲得的主要成果和結論如下： （ 1 ） sf _ 6 n _ 2 、 sf _ 6 ar混合氣的開關特性及多通道場畸變開關設計技術研究方面。Experiments of solid state heat capacity laser using spark switch
基於火花隙開關實現的固體熱容激光器實驗分享友人