焊后熱處理 的英文怎麼說

中文拼音 [hànhòurèchǔlǐ]
焊后熱處理 英文
after postweld heat treating
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 處 : 處名詞1 （地方） place 2 （方面; 某一點） part; point 3 （機關或機關里一個部門） department; offi...
  • 理 : Ⅰ名詞1 （物質組織的條紋） texture; grain （in wood skin etc ） 2 （道理;事理） reason; logic; tru...
  • 熱處理 : [冶金學] heat treatment; heat treating熱處理保護塗料 heat treatment protective coating; 熱處理車...
  1. Usages : exhaust pipes of aircraft, boiler covers, heat exchangers, boiler pipes, some parts that are impossible for heat treatment after welding or assembling

    航空器排氣管、鍋爐蓋罩、熱交換機、鍋爐用管、延展接頭等的焊接、接合后無法熱處理的零部件及設備。
  2. After a nationwide restructuring of colleges and departments in 1952, the department was renamed as the department of machine manufacturing, comprising 5 disciplines manufacturing technology, foundry technology and equipment, forging and pressing technology end equipment, welding technology and equipment, and etall. graphy and heat treatmento in addition, on the basis of the original power machinery teaching group, the department of power machinery was set up, having 3 disciplines : thermal electr

    1952年院系調整，更名為機械製造系，設機械製造工藝鑄造工藝及設備壓力加工工藝及設備焊接工藝及設備金相熱處理5個專業，並且由原動力組擴建成立了動力機械繫，正式設有熱力發電后改為鍋爐燃氣輪機汽車拖拉機3個專業。
  3. The purpose of the paper is to search the feasibility of the ecletron - beam weld of ti3al intermetallics and tc11 ( a + b ) two phase titanium alloy, and the influence to weld microstructure and properties of the hot deform and heat treatments

    本文的目的是探索ti _ 3al金屬化合物tac - 1b合金與tc11兩相鈦合金電子束焊、熱模鍛及熱處理的可行性，並研究焊后熱加工變形與熱處理對組織與性能的影響。
  4. The reheating embrittlement of a crack - free steel during post - welding heat treatment

    無裂紋鋼的焊后熱處理與再熱脆性
  5. The necessarily of post - weld heat treatment of spherical tanks was emphasized

    強調了焊接球罐焊后熱處理的必要性。
  6. The effect of post - welding heat treatment on the weld line, the microstructure and mechanical property of t91 steel was studied

    摘要研究了t91鋼焊后熱處理對焊縫及母材組織性能的影響。
  7. According to these, the paper put forward some countermeasures : select low carbon steel or low metal alloy steel with lower intensity, like 20r steel ; while welding, adopt strict craft measures with lower welding heat to input ; after jointing, proceed the whole hot dissolving on time ; control each welding joint with hardness hb 185 ; add 0. 25 % water into the liquid ammonia as decay eclipse ; enhance checking in operation, repairing equipment in time through regular interior and exterior checking

    針對上述原因提出了防止氨冷器類臨氨壓力容器產生應力腐蝕裂紋的對策：選用強度稍低，但抗裂性較好的低碳鋼和低合金鋼，如用20r鋼製造；焊接時應採用嚴格的工藝措施和較低的焊接熱輸入量；焊后應及時進行整體消除應力熱處理；控制焊接接頭各區硬度hb 185 ；在液氨中添加0 . 25 %的水作為緩蝕劑；在運行中加強檢查，及時進行停車檢修時的內外部檢查和定期檢驗。
  8. Methods of post weld heat treatment

    焊接后的熱處理方法
  9. The results of the experiments show that the ti3al - tcll dual alloys, by vacuum - electron - beam weld, hot die forging and 680c / 12h, ac, heat treatments, have satisfied synthesis properties of intensity, plasticity, hardness. and also it is the feasiblie way. this will establish the supporting technology for the manufacture of the compress disk in the areoengine

    實驗結果表明，經真空電子束焊接ti _ 3al ? tc11雙合金經過熱模鍛造和680 12h ， ac或815 1h + 700 8h ， ac熱處理后，焊接區組織過渡均勻，可以使得焊縫處強度在室溫拉伸時高於ti _ 3al ，而在600拉伸時高於tc11合金，獲得強度、塑性、硬度均令人滿意的綜合性能，且是一條可行的工藝路線。
  10. About design programs of propylene tower post weld whole heat treatment, we have made analyses and compare from the various technical and economic aspects, and in vertical state of large pressurized vessel, we propose to adopt the internal combustion heat treatment method, in horizontal state of it, to adopt high temperature flue gas heat treatment method, and propose center combustion tube method as the future direction of technical developmnet insights

    摘要圍繞丙烯塔焊后整體熱處理的各種設計方案，從技術、經濟等方面進行分析對比，提出對超大型壓力容器，立置狀態下宜採用內燃法熱處理；臥置狀態時宜採用高溫煙氣法熱處理，並提出將中心燃燒管法作為今後技術發展方向的見解。
  11. Advance in the technology of steels, post - weld heat treatment process and insulating materials used by spherial tanks was reviewed from 10 chinese patent, because patent technology represents technology progress of a country in a technology field

    鑒于專利技術能代表一個國家在某領域的技術進展狀況，故結合10項中國專利，從球罐用鋼、球罐焊后熱處理及球罐用保溫材料三個方面，詳細介紹了中國在該領域的新的發展。
  12. And has got favorable responses from the customers. iung cheng fa industry co., ltd

    目前應用於壁紙業、橡膠業、金屬熱處理業、螺絲業、電焊業…等業界使用后反應良好。
分享友人
分享到 Line

分享到臉書