焊接試驗室 的英文怎麼說

中文拼音 [hànjiēshìyànshì]
焊接試驗室 英文
welding laboratory
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 試 : 名詞（古代占卜用的器具） astrolabe
  • 驗 : 動詞1. （察看; 查考） examine; check; test 2. （產生預期的效果） prove effective; produce the expected result
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 試驗 : trial; experiment; test
  1. And the finite element method ( fem ) was used to simulate the stress and deformation of the outer casing and the bearing chock. on the basis of the experiments and fem analysis, the strength and fatigue lifetime, the interaction of creep and fatigue lifetime, the creep lifetime of outer casing and bearing chock have been analyzed, at the end of trail, sem analyses of failure section has been conducted

    同時對航空發動機燃氣渦輪外機匣和軸承座進行了有限元模擬計算，得到外機匣和軸承座的焊接處的強度和變形情況的模擬結果。根據試驗數據和有限元的計算結果，對發動機燃燒室外機匣和軸承座兩種結構（包含焊縫）進行靜強度分析、疲勞壽命分析、蠕變壽命分析、蠕變疲勞交互作用壽命分析以及斷口的金相分析。
  2. Abstract : by measuring the content of hydrogen diffused into the deposited metal under different temperature and humidity in the first environmental welding laboratory of our institute, the influence of the environmental conditions on the hydrogen diffusion was investigated

    文摘:通過在溫濕可調焊接實驗室中進行不同環境條件下的測氫焊接試驗，研究了環境條件對熔敷金屬中擴散氫含量的影響。
  3. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 1 : determination of emission rate and sampling for analysis of particulate fume

    焊接和相關工藝的衛生與安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第1部分:顆粒煙塵排放率的測定和顆粒煙塵分析用取樣
  4. However, a further investigation is still needed in order to interpret the test results of cross - weld specimens for application in practical welded components

    但是試驗室的焊縫試樣能否真實地反映焊接構件的力學行為，則仍是需要進一步研究的問題。
  5. In light of the uniaxial material tests and numerical simulations, the present paper reveals that the cross - weld specimen may be used for the high temperature strength assessment, but can hardly be used for simulation of the practical welded component, depending on the loading case of the component

    本文根據實驗室單軸試驗和計算模擬，揭示了單軸焊縫試樣的局限性：用於高溫強度評價基本上是合適的，但用於模擬實際焊接構件的力學行為則誤差甚大，這取決于焊縫的受力狀況。
  6. Based on the head loss coefficients obtained from gardel ' s semi - empirical equations for t - junction flow and experiment of welded t - junction, the hydraulic characteristics of throttled surge tank are estimated and compared with those gotten from hydraulic experiment. 3. four different methods of determining the head loss coefficients of throttled surge tank have been employed to investigate the effect of methods afore mentioned on the accuracy of calculating surge and pressure head of throttled surge tank

    給出了基於gardel關於三通管水頭損失系數的經驗公式、焊接t形三通管水頭損失系數的實驗資料及截面突變管道的水頭損失資料，計算有連接管的阻抗式調壓室在不同流態下水頭損失系數的計算方法，並將這兩種方法計算得到的調壓室局部水頭損失系數分別與模型試驗成果進行了比較和分析； 3
  7. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 2 : determination of emission rates of gases, except ozone

    焊接和相關工藝中的衛生和安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第2部分:除臭氧外的氣體排放率測定
  8. Health and safety in welding and allied processes - laboratory method for sampling fume and gases generated by arc welding - part 3 : determination of ozone concentration using fixed point measurements

    焊接和相關工藝的衛生和安全.電弧焊產生的煙塵和氣體取樣的試驗室方法.第3部分:用固定點測量法測定臭氧濃度
分享友人
分享到 Line

分享到臉書