焊接連接 的英文怎麼說

中文拼音 [hànjiēliánjiē]
焊接連接 英文
weld joint
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 連 : Ⅰ動詞1 （連接） link; join; connect 2 （連累） involve （in trouble）; implicate 3 [方言] （縫） ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 連接 : connect; fit together; link; marry; mate; joint; association trail; linkage; concatenate; concate...
  1. Welded - in seat is stellite 6 faced

    焊接連接閥座採用鎢鉻鈷合金6閥座面。
  2. The calculation results indicate that the outboard of drum walls fall in plastic yielding at the same time the rising cooling water reaches the height of that point and the yield region becomes narrower and narrower when it comes closer to the circumferential strake weldments, which explains the reason coke drums experience bulging and cracks occur in the weld seams portions of shell to shell after long in service

    計算結果表明：塔壁外側在冷卻水面到達的瞬間進入塑性屈服，筒節中部塑性屈服區較大，當靠近焊縫時塔壁的塑性變形區逐漸縮小直至消失，塔壁塑性屈服區的分佈特點解釋了塔體長期使用后發生鼓凸變形及簡體與焊縫連接處產生裂紋的原因。
  3. Heat solder joints only to the point were solder will flow properly. excessive heat may distort brass castings

    熱焊料連接只能用在焊料能夠正確流動的地方。過熱可能扭曲黃銅鑄件。
  4. Results showed that the ductility of bolt spjice is much better than welds, weaker splice joints develop larger plastic deformation, slipping between faying surfaces, bearing of bolts to hole surfaces and buckling of splicing plates are all ideal energy dissipation mechanism

    試驗結果表明：螺栓拼接節點的延性遠好於樑柱焊縫連接；較弱的拼接節點產生較大的塑性變形；接觸面的滑移、螺栓與孔壁的擠壓和翼緣拼接板的屈曲都具有良好的耗能能力。
  5. Metallic construction. welded joints. fabrication

    金屬結構.焊接連接.製造
  6. Steel construction. welded connections. approval of a welding procedure

    鋼結構.焊接連接.焊接程序批準
  7. Solder end valves also available

    也可以提供焊接連接埠的閥門。
  8. Metal construction. welded assemblies. ranges of non destructives control

    金屬結構.焊接連接.無損檢測范圍
  9. General requirement and test methods of solderless wire - wrap for electrical controlgear

    電控設備用無焊繞接連接.一般要求及試驗方法
  10. Crimp - type cable sockets for solderless connections, insulated, for copper conductors

    銅導線用絕緣非焊接連接的壓接電纜端頭
  11. Solderless connectors, without insulating sleeve, for copper conductors

    第1部分:銅導線用無絕緣套管的非焊接連接器
  12. Pin type cable - sockets for solderless connections, insulated, for copper conductors

    銅導線用絕緣的非焊接連接的插針式電纜端頭
  13. When installing solder end valves, conventional soldering techniques should be used

    安裝焊接連接埠的閥門時，應該採用普通焊接技術。
  14. Solder end valves are limited by temperatures which affect the strength of the solder joint

    4焊接連接埠閥門溫度限制在不影響焊接連接埠的強度范圍內。
  15. The 1710 series threaded and solder end range are ” t “ pattern globe style valves

    1710系列螺紋和焊接連接埠為t形截止閥結構的閥門。
  16. Mechanical connection will be adopted for column rebar according to construction drawings

    5柱縱向鋼筋按圖紙要求焊接連接。
  17. Steel construciton. welded connections. details and design of welds

    金屬結構.焊接連接.焊接細節和設計
  18. Aerospace series - pipe coupling, in heat resisting steel or in heat resisting nickel alloy - coupling end, welded - design configuration - inch series

    航空航天系列.耐熱鋼或耐熱鎳合金管接頭.焊接連接端.設計構型.英制
  19. 4, in welding connection, the placing screw shall be appropriately loosened to prevent distortion. 5, in welding, covering shall be applied to cover the rubber fabric to prevent the damage to product

    4焊管連接時，應將限位螺絲適當松動，防止將補償器限位板拉彎或產品變形。
  20. The superiority of the connection of nut with protection by laser welding is expounded

    摘要論述了激光焊接連接防護罩和螺母的優越性。
分享友人
分享到 Line

分享到臉書