焊接類型 的英文怎麼說

中文拼音 [hànjiēlèixíng]
焊接類型 英文
welds types
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  • 接 : Ⅰ動詞1 （靠近;接觸） come into contact with; come close to 2 （連接; 使連接） connect; join; put ...
  • 類 : Ⅰ名1 （許多相似或相同的事物的綜合; 種類） class; category; kind; type 2 （姓氏） a surname Ⅱ動詞...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  • 類型 : type; mold; form; cut類型論 theory of types; 類型語句 [計算機] type statements
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. To validate the formulated transition element for the calculation of the hot - spot stress and stress concentration factor in the welded components by experimental results, the stress concentration factor of the experimental welded specimens carried out in the research group is calculated by using the developed plane - transition element. the calculated stress concentration factor in the two types of tested welding components agrees well with that obtained from the experimental result. and the calculated result on the tendency of hot - spot stresses agrees well with that from the measured result

    為了驗證文中構造的過渡單元模型用於分析焊接節點附近的應力集中問題的正確性和有效性，進一步又對過渡單元模型進行實驗結果驗證，採用平面過渡單元模型計算了本課題組進行的兩類焊接構件的應力集中系數，並與根據實測方法得到的應力集中系數進行了比較，計算結果與實驗測試得到的應力集中系數和相應的熱點應力變化趨勢比較吻合，為本文建立的過渡單元的實際應用提供了初步的基礎。
  3. In this thesis, four types of steel beam - rectangular cfst column connections, including normal welded flange plate ( wfp ) connection, bolted flange plate ( bfp ) connection, stiffened end plate ( sep ) connection and double split - tee plate ( dst ) connection, were designed based on the configuration of steel frame connection. total 8 models, 2 models of each kind of connections were tested under low - reversed cyclic loading at the end of cfst columns. the relationships between force and displacement at the end of columns, the relationships between the moment and rotation of the joints, degradations of strength and stiffness, ductility, failure mechanism and failure characteristics of these four connections under different axial - compression ratios were presented

    本文借鑒鋼框架節點構造，設計了四種類型矩形鋼管混凝土柱與鋼梁連接節點，包括常規栓焊（ wfp ）節點、翼緣全螺栓連接（ bfp ）節點、雙t板連接（ dst ）節點以及加勁端板連接（ sep ）節點，進行了四類節點8個模型試件在柱端低周反復荷載作用下的抗震性能試驗研究，比較了不同軸壓比下節點的滯回性能、強度與剛度退化、延性、破壞機理與破壞特徵，主要結論有： 1 、節點的位移滯回曲線與轉角滯回曲線為塊型分佈，沒有或略有捏攏現象，耗能能力強； 2 、軸壓比對節點滯回曲線有顯著影響，全部節點都有顯著的剛度退化； 3 、位移與轉角骨架曲線在峰值荷載後有較長的水平或下降段，具有良好的延性性能； 4 、從整體抗震性能上看，翼緣全螺栓連接節點、雙t板連接與加勁端板連接節點都優于常規栓焊節點，可在實際工程中加以推廣。
  4. The design process of the proposed method is described as follows : the input of the method is the 3d sketch of a light steelwork, and the geometry and topology information of the members in a steelwork are established automatically. the steel types and function of the linked members are determined by means of interactive scheme according to the design requirements. and the arrangement of the steel members and their orientation are built according to the steel member ' s type, the function of the steel member, the knowledge of the steelwork and welding technology

    在該方法中，首先通過交互手段輸入輕型鋼結構的三維線框簡圖、自動確定結構的幾何和拓樸信息，根據設計要求輸入各桿件的型鋼類型和在結構中的功能；然後，根據型鋼類型、桿件功能、鋼結構設計知識以及焊接知識自動確定桿件的搭配關系、建立桿件的方位布置確定規則和節點板設計的規則；最後，利用這些規則來決定節點稈件連接關系、連接位置，確定節點板的類型、布置方位和位置，實現三維鋼結構的結構自動設計。
  5. Valves shall be one of the types specified in 4. 2 to 4. 4, having flanged, threaded, capillary or compression ends, integral or renewable body seats and screwed, union or bolted bonnets or covers

    閥門的類型應是4 . 2到4 . 4中所給出的類型，帶有法蘭/絲口/焊接或壓縮端面，帶有完整的或可更換的閥體，及螺紋式，聯接式或拴結式閥帽或閥蓋。
  6. Production : ig gasket technology ( shenzhen ) is currently managing a considerably wide range of products, from natural rubber to silicones, from plastic components to rubber / metal bonding

    產品：目前，愛吉密封膠圈科技（深圳）有限公司涉及的產品類型已經相當廣泛，從天然橡膠到硅樹脂，從塑膠合成物到橡膠/金屬焊接等。
  7. This ship is built of aluminum alloy all - welded mono - hull, knuckle lines, single bottom, single deck, single engine, single propeller, single rudder, transom stern, raked stem and raked keel, deployed to transport passengers on class iii navigational area set forth by hongkong marine department

    15 . 6m本船為鋁合金焊接單體船，型線為折角線型單底單甲板單機單槳單舵方艉，前傾艏柱傾斜骨，用於香港海事處規定之iii類航區接送旅客。
  8. Being engaged in welding technique, including the study of repairing high temperature and high pressure cast workpieces, alloy steel parts, big axle parts and so on

    主要從事焊接技術咨詢，其中包括對大型高溫高壓鑄件，耐熱鋼零部件；及大型軸類零件的補焊修復的咨詢及研究。
  9. Sonic new ideas and views were proposed, such as regulation on general welding procedure qualification and its method of application, welding procedure qualification between heat exchange tube and tube sheet assessmented by the thickness of fillet weld, and so on

    本文還首次提出一些新思路、新觀點，如母材、焊材分類細則以及標準以外材料分類要有分類報告佐證；通用的焊接工藝評定規定及使用方法；換熱管與管板的焊接工藝評定是評定角焊縫厚度；氣瓶焊接工藝評定是兩個類型評定的結合，也可以分別評定。
  10. Resistance welding - destructive tests of welds - failure types and geometric measurements for resistance spot, seam and projection welds

    電阻點焊.焊接有損試驗.電阻點焊縫焊和凸焊的故障類型和幾何測量
  11. This product is collod feathering achro, aticity and viscosity, wghhich can clear the thick oxideatice horizon hot pressed end plate or rollsteel plank which be processed or welded under hot temperature and hot pressure

    本產品為無色透明的粘稠狀膠體，針對不銹鋼熱壓封頭或用熱軋板製作工件等，經過高溫高壓處理或焊接時所產生紅、黑、黃等各種類型的較厚氧化層，清除迅速，徹底。
  12. Formation, soldering, coating, surface treating and related business for pipes, metal bars and metal sheeting

    各種管類條類金屬鈑金之成型加工焊接及塗裝業務表面處理及業務
  13. The maximal power outputs of 37. 0 mw / cm2 and 30. 0 mw / cm2 for the p - and n - type laminated materials respectively at the temperature difference 490 have been experimentally obtained, which are about 2. 5 and 3. 0 times those of - fesi2. chemical analyses show that the interface failure between the bridge alloy and the semiconductor bi2te3 results mainly from the eutectic mixtures with low melting point and brittle compounds formed during welding and long time annealing at 190. it is found that the electrical properties of a laminated structure are mainly controlled by the wettability of the bridge alloy on the semiconductor surface

    發現： 1 ）疊層材料具有明顯優于均質材料的熱電性能，在490溫差下， p -型和n -型疊層材料的最大輸出功率分別達到37 . 0和30 . 0 （ mw / cm ~ 2 ） ，是同類型均質- fesi _ 2的2 . 5和3倍； 2 ）在焊接過程和190長時間退火處理過程中，焊接過渡層合金和基體半導體（特別是bi _ 2te _ 3 ）之間存在明顯的元素相互擴散，從而在過渡層中形成一些低熔點共晶體和脆性化合物，這是導致疊層材料破壞的主要原因； 3 ）焊接過渡層合金與半導體基體之間的潤濕性是影響界面層電性能的主要因素。
  14. The effectiveness of predicting model is proved by means of comparison between predictions and experiments for a few types of welded steel structures

    通過對幾類典型焊接鋼結構疲勞強度的理論預測與疲勞試驗結果的比較，驗證了理論模型的正確性。
  15. The stress fields in misaligned welded joints, " t " type of plate welded joint, flanged beam and perpendicular flanged beam are calculated respectively, and their stress concentration factors formulation are obtained

    採用這兩類單元計算了錯位板接頭、 t型板接頭、工字梁焊接鋼結構和工字梁十字接頭的應力場，得到了相應的理論應力集中系數公式。
  16. Four groups of eight types of connection methods are suggested to be able to use for the joint of cold - formed rectangular tube - steel column and h - shaped beam by investigating the current research on the beam - to - column connection methods used at home and abroad, at the same time, a new type of connection is proposed in this article

    本文在對國內外冷彎矩形鋼管與焊接箱形鋼管節點型式研究的基礎上總結出四類八種適合於冷彎矩形鋼管柱與h型鋼梁連接的節點型式，並提出一種新型節點連接型式，分別給出了相關的設計規定和使用條件。
  17. Shear properties in the plane of the panel ( interlaminar shear ) duplicate the kind of shear stress encountered in such glued structural assemblies as structural sandwiches and adjacent to gluelines between flanges and webs in box - beams and i - beams and gusset plates in trusses

    面板平面的剪切特性（層間剪切） ，與夾層結構這類粘合組件，以及箱形梁、工字梁凸緣與腹板間的焊接層和桁架加固板附近位置所受的剪切應力類型相同。
  18. As a branch of intelligent control, fuzzy control is based on human ' s thought and does n ' t rely on mathematical model. and so it is a good method for auto - tracking in welding

    而模糊控製作為一種基於人類思維來設計的智能控制方法，控制策略不需要數學模型，為焊接自動化提供了一條較好的途徑。
  19. Control and reduce the deformation of welding for frame of ball nodal in such kind of steel tube as diagonal laying of quardcone and quaraune diagonal laying with double phase

    兩向正交斜放類型鋼管球節點網架焊接變形的方法
  20. The main content included the purpose of all kinds of welding procedure qualification standards, two types of welding procedure qualification, and the differences and similarities between the two types

    主要內容有各類焊接工藝評定標準的目的、兩個類型的焊接工藝評定，以及兩類評定之間的區別與聯系。
分享友人
分享到 Line

分享到臉書