焊熱 的英文怎麼說

中文拼音 [hànrè]
焊熱 英文
welding heat
  • 焊 : 動詞（用熔化的金屬修補金屬器物或使金屬工件連接起來） weld; solder
  1. The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique

    通過對其焊接性能的試驗研究，制定了該類鑄鋼件（磨耗板）的補焊工藝：低氫型堿性焊條，預熱與緩冷相結合的工藝措施，嚴格控制層間溫度（ 250 ~ 300 ）及焊接工藝規范，可獲得滿意的修復質量。
  2. Quick diathermancy avoid damage to cmos chip and solder. precise design and good technics avoid damage due to attrition. vacuumize avoid alterative because of oxygenation during transportation. antistatic plastic core

    傳熱吸收快，盡可能的避免對晶元和焊盤的損壞;精確的設計和製造工藝避免磨擦對焊盤可能造成的損壞;真空包裝避免?品在運輸途中氧化變質;防靜電塑料芯;符合美國軍隊及國家宇航局各種標準
  3. " blowtorch : a portable burner for mixing gas and oxygen to produce a very hot flame, used for soldering, welding, and glass blowing.

    噴燈:使混合氣體和氧氣產生更熾熱火焰的便攜助燃劑，常用於接合、焊接和玻璃吹制。
  4. Aluminium alloy foil for brazing type heat exchanger

    釬焊式熱交換器用鋁合金箔
  5. Methods for chemical analysis of melted welding fluxes. the pyrolytic method for determination of calcium fluoride content

    熔煉焊劑化學分析方法.熱解法測定氟化鈣量
  6. Pre - data gathering module achieves the collection and communication of sixteen - route temperature signal. speed measuring and controlling module realizes the control of refolw soldering transfer speed by manipulating transducer. on - off outputting module fulfills calefaction control of calefaction tube by solid state relay. above position operator software programs by delphi, and realizes pid parameter automatic timing and no - oversnooting temperature control. software has friendly interface, convenient operation, complete functions

    前置數據採集模塊完成16路溫度信號的採集和通訊；速度測量模塊與速度控制模塊通過控制變頻器來調節迴流焊的傳輸速度；開關量輸出模塊通過固態繼電器對加熱管進行控制；上位機軟體採用delphi編程，實現了pid參數自整定以及無超調的溫度控制。
  7. 3, change the sub - form into a type of origin benefit type, the department is hollow and can heat or cool off, turning a heap to bear to whet hard quality metal alloy in the, the work surface plates hard chrome, bearing corrosion to bear to whet function like

    3轉子形式為類本伯利型，棱部中空可加熱或冷卻，轉于棱峰堆焊耐磨硬質合金，工作表面鍍硬鉻，耐腐蝕耐磨性能好。
  8. 2d - cad, 3d - cad cae, injection molding machines, 3dmeasurement machines, ultrasonic welding machines, high - frequency electromagnetic welders, hot stamping machines, silkscreen printing devices, caulking machines, automatic screw machines, det raw material - exclusive dryers, load testers

    2d - cad ， 3d - cad cae ，射出形成機， 3維測量機，超聲波焊著機，高頻電磁電焊機，熱沖壓機，絲印刷裝置，鉚合機，自動打釘機， det原料專用乾燥裝置，負荷試驗機。
  9. Before repairing, basing on the actual working condition, concerning the weldability, stress and deformation issues, the scheme of the cold welding technology whose essential being gtaw, low temperature preheating, postweld hammer the welded seam was established

    修理前，圍繞兼顧解決焊接性、應力和變形問題，結合實際施工條件制定了以手工鎢極氬弧焊、鎳基焊絲、焊前低溫預熱、焊后錘擊焊縫為要素的冷堆焊工藝。
  10. Phenolic foam is a new generation heat preservation prevent fire soundproof material and polystyrene together ammonia ester foaming rubber etc, material to compare, and it is good that its biggest characteristics is a heat - proofound the low temperature contractility is smatt, and have te special prevent burning wit the size stability under 2000 heat, not burning, not melt not contract constant form not poisonous spirit hove no thick smoke, just surface formation layer

    信息內容：酚醛泡沫為新一代保溫防火隔音材料與聚苯乙烯聚氨脂發泡橡膠比，其最大特點是耐熱性好，低溫收縮性小，具有獨特的阻燃和尺寸穩定性，在焊槍火焰下，不燃燒不收縮不變形，無毒氣無濃煙，只是表面炭化，性質穩定，耐化學腐蝕抗老化。
  11. Medium frequency induction heating equipment are used in metal melting, temperature keeping, diathermic technology, metal - heat processing brass soldering, quenching, tempering and sintering

    中頻感應加熱設備適用於各種金屬熔煉，保溫，透熱，金屬熱處理，釬焊，淬火回火，燒結，釬絲鋼絲等。
  12. Simulation of grain growth in the haz of stainless steel eb

    1不銹鋼焊接熱影響區晶粒生長模擬
  13. ( 2 ) design of the implantating device : some quantity of 316l stainless steel, perform forging and thermal rolling, drawing filament ( diameter 0. 4mm and 0. 23mm respectively ), enlacing and jointing, after that assembling the products into guiding filum, a technical examination was carried out to appraise their physical capability. the second part : experimental study : animal experiments were used to screen and observe its validity and security : under general anesthesia, tracheotomy was performed on the healthy dog, the bronchus was localized using x - ray fluoroscopy fibrobronchoscope and with the help of the implanting equipment, several niti alloy occludes were implanted into the target bronchus of the dogs through the biopsy channel in the fibrobronchoscope

    （ 2 ）推送器的研製：取316l不銹鋼熱軋，分別拉製成不同直徑的不銹鋼絲分別用作製作內芯、外環及車制螺絲，再經纏繞、焊接、裝配成推送器。對上述兩者進行技術鑒定。第二部分：支氣管封堵器的實驗研究：四種形狀的封堵器分四組（上述四種封堵器各12隻）進行動物實驗，分別觀察其安全性與有效性。
  14. The 11th beijing essen welding & cutting fair is open today. on behalf of china welding association, i warmly congratulate its opening

    第十一屆北京?埃森焊接與切割展覽會勝利開幕了，我謹代表中國焊接協會表示熱烈祝賀！
  15. Qishuyan locomotive & rolling stock works, situated in changzhou city, jiangsu province and founded in 1905, covers an area of 1, 760, 000 square meters, owns 4, 500 unitssets of various mechanical equipment, and possesses a comprehensive production capability of forging & casting, machining, riveting & welding, heat treatment, tooling & patterns and sophisticated measures for physical & chemical tests, metrological measurements & inspection. it is an important base for manufacturing artery dedicated diesel engine locomotives, freight wagous, heavy duty diesel engines and railway components, which have won the credit and trust from customers by their excellent quality and outsanding aftersales service and enjoy good sales throughout the country and in countries in europe and america

    公司介紹：戚墅堰機車車輛廠地處經濟發達、科技進步、風景秀麗、人傑地靈的江蘇省常州市，創建於1905年，佔地176萬平方米，擁有各類機器設備4500臺，具有鍛鑄、機加工、鉚焊、熱處理、工裝模具等綜合生產能力，以及齊全的理化試驗、計量和檢測手段，是我國鐵路干線內燃機車、貨車、大功率柴油機和鐵路配件的重要生產基地，以優質的產品和優良的服務羸得客戶信賴，產品銷售遍及全國並遠銷至歐美等國際市場。
  16. The purpose of the paper is to search the feasibility of the ecletron - beam weld of ti3al intermetallics and tc11 ( a + b ) two phase titanium alloy, and the influence to weld microstructure and properties of the hot deform and heat treatments

    本文的目的是探索ti _ 3al金屬化合物tac - 1b合金與tc11兩相鈦合金電子束焊、熱模鍛及熱處理的可行性，並研究焊后熱加工變形與熱處理對組織與性能的影響。
  17. Hf electrothermal equipment production company, be applied to smelting. qian welding. heat treatment. forging hf hanguan. large direct current generator mechanics

    我公司生產中高頻電熱設備，可應用於熔煉.釬焊.熱處理.鍛造高頻焊管.大型直流電動機調速等
  18. I hf electrothermal equipment production company, be applied to smelting. qian welding. heat treatment. forging hf hanguan. large direct current generator mechanics

    我公司生產中高頻電熱設備，可應用於熔煉.釬焊.熱處理.鍛造高頻焊管.大型直流電動機調速等
  19. Semiconductor devices - mechanical and climatic test methods - part 20 : resistance of plastic - encapsulated smds to the combined effect of moisture and soldering heat

    半導體裝置.機械和氣候試驗方法.第20部分:塑料密封的smds抗濕氣和釬焊熱綜合影響的性能
  20. Semiconductor devices - mechanical and climatic test methods - resistance of plastic - encapsulated smds to the combined effect of moisture and soldering heat

    半導體器件.機械和氣候試驗方法.塑料包封的smds的抗濕及釬焊熱度綜合影響
分享友人
分享到 Line

分享到臉書