焊補 的英文怎麼說
中文拼音 [hànbǔ]
焊補
英文
soldering; scalding; weld up-
The welding performance of homemade wear - resistant cast steel has been studied base on the weldability tests, the repair welding procedures of wean - resistant cast steel ( abrasion - plates ) have been made up, the results show that satisfying repair welding quality can be attained with such welding conditions as the low hydrogenous alkalescent welding rod, preheating and slow cooling, strictly maintaining the interbedded temperature of 250 ~ 300 and controlling welding technique
通過對其焊接性能的試驗研究,制定了該類鑄鋼件(磨耗板)的補焊工藝:低氫型堿性焊條,預熱與緩冷相結合的工藝措施,嚴格控制層間溫度( 250 ~ 300 )及焊接工藝規范,可獲得滿意的修復質量。The crack between the coped and hole was removed by air arc and then repaired by welding.
在修割邊和鉆孔之間的裂紋用氣弧消除,然後進行焊補。Repair welding requirement for grade 3 cast steel chain cables
三級鑄鋼錨鏈補焊技術要求Welding terms and symbols - supplement - definitions for electric welding equipment
焊接術語與符號.補充.電焊設備的定義Dye-penetrant and magneticparticle inspection techniques were used on the repaired and other 21 remaining original welds.
在已修補了的和其餘21個原來的焊縫上進行了著色滲透和磁粉探傷工藝處理。It covers the requirements for approved inspectors, approved signatories and other requirements specific to consumer product inspection. specific requirements for construction products inspections are given in hkias supplementary criteria no. 2 on general construction products and supplementary criteria no. 3 on welding inspection. inspection bodies interested in obtaining accreditations for consumer products inspection may contact hkas senior accreditation officer,
消費產品檢驗的特定規定可見于檢驗機構認可計劃《補充準則第1號》 ,當中載有核準檢驗員和核準簽署人員的規定,以及其他適用於消費產品檢驗的特定規定;至於建築產品檢驗的特定規定則可見于有關一般建築產品的檢驗機構認可計劃《補充準則第2號》 ,以及有關燒焊檢驗的檢驗機構認可計劃《補充準則第3號》 。Automatic offset function for long cable up to 100m
具有焊線長的自動補償功能,焊接電纜可長至100米Specification for arc welding repair of high manganese steel crossing
高錳鋼轍叉電弧焊補技術條件Study on cast iron welding measure
鑄鐵焊補尺寸的研究It is most handy to use an oxy - acetylene cutter to cut this plate
你們應當派有豐富經驗的人來焊補裂開的活塞頂Maintenance on line to rail with high frequency inverter dc welding machine
高頻逆變焊機用於鋼軌及轍叉線上焊補與維護Internal combustion engines. welding repair for gray iron casting defecfs. specifications
內燃機.灰鐵鑄件缺陷焊補.技術條件After weld repairs, however, the overall quality and reliability of a cast valve is difficult to determine
但是,在焊補后,鑄件閥門的整體質量和可靠性就變得難于保證。Upgrading of castings to meet x - ray quality needs relies on the grinding out of faulty areas, weld repairs, heat treatment, and retest and examination
鑄件的改進要滿足x射線質量的要求就要靠缺陷部位的磨削,焊補,熱處理和重復測試和檢驗。The weld step and process were introduced, the experience of weld retrofit of the valve was rarely gained, and can be used for reference
介紹了缺陷處理的具體工藝措施、過程,簡述了汽包筒體缺陷處理方面的經驗,為國內運行機組同類缺陷的焊補提供了借鑒。Records of weld - repair locations must therefore be maintained, so signs of distress found during plant operation can be related to the original fabricated conditions and standards
焊補位置的紀錄因此必須保存,所以在工廠運行過程中,故障發生的信號可能與原始的製造條件和標準有關。The conclusion of reappearing analysis is that crane bridge be used as usual because main weld maximum stress of upper cover plate of main beam lower than yield limit though it higher than permissible stress. inner stress of secondary beam was over ultimate strength, and deforming is ultra big. so it was unfit for produce and secondary beam must be changed
再現分析得出的主要結論為:橋架的主樑上蓋板主焊縫的最大應力超過了許用應力,但小於屈服極限,可以繼續投入使用;副梁內部的應力遠遠超過了強度極限,變形特別嚴重,不能滿足生產要求,因此更換新的副梁;端梁內部的應力超過了屈服極限,小於強度極限,在應力較大的位置焊接補強板;投入使用后,要對整個橋架進行定期檢查。The theme is an important part of province project for tackling key problem concerning the development of minitype welding and repairing instrument suiting for working in the turbine pit, the theme is worked in the welding and grinding robot. with d - h method the kinetic coordinate and equations are built which is the base of controlling robot
本課題是省科技攻關項目「機坑內修復小型焊補機的研製」的重要組成部分,本文的研究工作是針對水輪機修復專用機器人進行的,應用d - h方法建立了此機器人的各關節之間的坐標關系及其運動學正問題方程,為機器人系統的運動控制提供了可靠依據。Repair welding of bolting material is not permitted
螺栓材料的補焊是不允許的。Abstract : the effect factors which influence service life of sintering fan were analysed. the technique and experience of in situwelding repair wheels in lai steel were presented
文摘:本文簡要分析了影響燒結風機轉子使用壽命的因素,介紹了萊鋼對9500風機轉子進行機上焊補的技術和經驗。分享友人