無槽電動機 的英文怎麼說

中文拼音 [wúcáodiàndòngjī]
無槽電動機 英文
slotless motor
  • 無 : 無Ⅰ動詞（沒有） not have; there is not; be without Ⅱ名詞1 （沒有） nothing; nil 2 （姓氏） a surn...
  • 槽 : 名詞1 （盛牲口飼料或飲料等液體的器具） trough; manger （for water animal feed wine vat） 2 （兩邊...
  • 電 : Ⅰ名詞1 （有電荷存在和電荷變化的現象） electricity 2 （電報） telegram; cable Ⅱ動詞1 （觸電） give...
  • 機 : machineengine
  • 電動機 : electric motor; motor （俗稱「馬達; 電滾子」）電動機並聯法 parallel connection of the motors; 電...
  • 電動 : motor driven; power driven; power operated電動擺 motor pendulum; 電動扳手 electric wrench; 電動泵...
  1. Disigning coolant channel on the firebox of liquid rocket engine to loxodrome ( equal - angle helix ) groove can improve firebox coolant capability greatly. because the width dimension of loxodrome groove is narrow and the depth is deep, some machining methods are incapable, such as end - milling or electrochemistry. according to the peculiarities, a cnc disk - cutter - milling method which is composed of five motion axes with four simultaneously interpolated ones is researched. because most firebox generatrix is composed of complex curves, it is very difficult to get cnc cutting program with manual means. in order to deal with the problem, the loxodrome mathematics model is studied, and an auto - programming software system is developed. the software system can generate cnc cutting program of loxodrome on many kinds of turned surface. the constriction - distension segment of firebox is the most representative workpiece. the sharp changing of its generatrix slope makes loxodrome milling difficult. with the theory analyzing and practice cutting experiment, some applied techniques, which include milling mode and direction, choosing cutter diameter and cutting start point setting, are developed. adopting the technology above, tens regular workpiece have been manufacturing. the two - year manufacture practice has confirmed the validity and feasibility of developed loxodrome coolant channel milling method. the developed technology is also worth to be referenced to other similar workpiece

    將液體火箭發動機燃燒室的冷卻通道設計為斜航線（等傾角螺旋線）槽形，可以大幅度改善燃燒室的冷卻性能.斜航線冷卻槽的槽寬尺寸較小而槽深尺寸較大，所以無法使用棒銑刀銑削、電化學等加工方式.針對這些特點，提出了五軸控制、四軸聯動的數控片銑刀銑削加工方法.由於燃燒室外表面的母線輪廓復雜，手工編制數控加工程序難度大.為了解決數控加工程序的編制問題，研究了斜航線的數學模型，開發了自動編程軟體系統.使用該系統，可以生成多種母線輪廓回轉體外表面上的斜航線數控加工程序.燃燒室收斂-擴張段的母線斜率變化大，加工難度大，是斜航線冷卻通道加工的最典型工件.經過理論分析和實際切削實驗，研究了針對該類型工件的片銑刀直徑選擇、銑削方式和方向、刀具調整和起刀點的設置等多項實際的加工方案.採用上述的一系列技術，已經成功地加工了數十個合格工件.經過兩年多的實際生產過程應用，驗證了所開發的斜航線冷卻通道加工方法的正確性和可行性.這些加工技術的研製成功，對其他相似類型零件的加工亦具有參考意義
  2. For the bldcm which has a general crest width of the back - emf waveform, two kinds of torque ripple conditions when drived by sine - wave current as well as by square - wave current are deduced based on the mathematical models. in addition, a comparison is carried out between these two conditions, which indicates that sinusoidal current driving is more favorable to minimizing the torque ripple when the crest width of the back - emf waveform is less than a certain value

    闡述了抑制齒槽轉矩措施對反電動勢波形的影響，利用無刷直流電機的數學模型推導並比較了任意平頂寬度梯形波反電動勢在正弦波和矩形波兩種電流驅動下的電磁轉矩脈動情況，得出在梯形波平頂寬度減小到一定數值后採用正弦電流驅動更有利於減小電磁轉矩脈動。
  3. The speed of isa bus has become the bottleneck between high a / d converters where requests very high speed. isa bus interface card ca n ' t configure resource automatically. there will be no place for isa bus after the vanish of isa slots on computer mainboard

    Isa總線有很多優點，但在某些方面已逐漸顯出不足：在一些速度要求高的場合， isa總線的速度上限已成為高速a / d轉換器與主機間的瓶頸； isa總線介面卡無法實現資源的自動配置；以及計算機主板的isa插槽在逐漸的消失，所以本文又提出設計基於pci總線的介面電路。
  4. The non - ideal bemf waveform of bldcm is often caused by two facts. one is that the platform width of bemf waveform is less than 120 ; the other is the cogging harmonics existed in the bemf waveform

    非理想反電動勢波形的無刷直流電機有兩種情況，一種是反電動勢的梯形波的平頂寬度小於120 ；一種是由於磁場分佈受齒槽的影響，反電動勢存在齒諧波，使其波形發生畸變。
  5. The satss is an antenna pointing servo system with ultra - low speed and high accuracy, driven by a rare earth permanent magnet ( repm ) brushless dc torque motor. to reduce torque ripple, the repm brushless dc torque motor has a slotless armature, and uses sinusoidal wave driven technology

    衛星天線跟蹤伺服系統為超低速高精度天線指向控制系統，該系統使用稀土永磁式無刷直流力矩電機作為天線的驅動機構，為降低轉矩脈動，電機採用無槽電樞結構設計，並使用正弦波驅動方式。
分享友人
分享到 Line

分享到臉書