熔化孔 的英文怎麼說

中文拼音 [rónghuàkǒng]
熔化孔 英文
melt off pore
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 熔化 : melt; smelt; meltdown; fusion; fusation; diatexis; eliquation; run; melting; smelting
  1. Infiltration and solidification remelting of molten aluminum in a centrifugal force field

    高溫鋁熔液在旋轉多孔介質內的滲透與瞬態固化和再熔過程
  2. Abstract : the formation technologies, the structure and properties of tcs microporous man - made yarn - kind new polyester fibre which was spinned in tcs with some micrometallic - oxide have been studied. the results indicate that the rheological behaviour and spinnability of commixed polyester melt, and the structure and properties of the fibre, are relative to the spinning temperature, melt pressure, microporpus size for spinning, formation conditions, thermo - vascellum temperature, thermo - vascellum position and rolling speed, besides the viscosity of polyester cuts, coacervation particles, adding amount and size of micrometallic - oxide

    研究表明， tcs微孔化共混聚酯熔體在成型加工中的流變行為和可紡性，及其纖維的結構性能除了與原料切片的特性粘度、凝聚粒子和共混聚酯中超細金屬氧化物微粒的添加量、粒徑等因素的影響有關外，還與紡絲溫度、紡絲熔體壓力、噴絲板微孔尺寸、冷卻成形條件、熱管溫度、熱管安裝位置以及卷繞速度等因素的影響密切有關。
  3. But there are some technical difficults for the welding of aluminium alloy such as some broken bits being easily found, a large welding distortion can happen easily, hard to distinguish the difference between the solid metal and liquid metal colour, hard to control the temperature, a lot of air holes can be seen in the welding line and so on

    但是鋁合金熔化焊時的技術難點在於：焊接時易引起夾渣，焊接變形大，金屬的固態和液態的色澤不容易區別，焊接操作時控制溫度困難，容易產生氣孔等等。如果焊前清理工作不是很好，檢測氣孔往往超標。
  4. 1. the splitting from the binding interface of cuw / crcu roots from the rich cr and the oxidation of the binding interface, which leads to the higher thermal resistance in binding interface than normal, and the thermal stress enhanced. the extruded cu is suggested to instead of casting cu

    （ 1 ）斷裂是由於原材料鑄態的crcu中c :質點大於熔滲的孔隙而沉積在界面上，同時在有氧源存在的條件下，結合面氧化，致使結合面結合不好，界面熱阻升高， cuw與crcu部分的膨脹不同，應力集中，燃弧后斷裂。
  5. The experiment result showed that, in the infiltration melting the evaporation speed of si is more rapid than mo. the melting which enrich the mo reacted with the sic body and there existed mo5si3c. the content of mosi2 can be controled by adjusting the contend of c in the perform ; the content of c is more high the pore volume in composite is more high

    研究發現，由於熔滲體中si的揮發速度快造成材料物相組成變化，熔滲體與sic坯體反應析出mo _ 5si _ 3c 、 mo _ 5si _ 3相阻塞坯體毛細管，使燒結體中產生氣孔。
  6. Furthermo re, the zinc vaporating and oxydizing cause air bubble, incomplete fusion and cr ack

    鋅揮發和氧化會導致氣孔、未熔合及裂紋。
  7. The thermodynamic conditions of decomposition of the foaming agent tih2, homogeneous and heterogeneous nucleation in high - temperature solid and liquid, growth and movement were achieved to demonstrate the trend of pore evolvement in this paper. moreover, according to the characteristics of in - situ gas foaming, the equations of the height change of foaming samples with heating time were primarily established to study the behavior of foams and to guild the experiment processes

    另外，論文通過大量的熱力學分析，得出了發泡過程中發泡劑分解以及氣孔在固液態時的均勻形核和非均勻形核、氣孔的生長和運動等熱力學條件，揭示了氣孔演化的趨勢；論文還根據內生氣源發泡的特點，初步建立了高溫熔體中氣體發泡高度隨時間變化的方程，為進一步深入的研究發泡機理奠定了一定的基礎。
分享友人
分享到 Line

分享到臉書