熔化工段 的英文怎麼說
中文拼音 [rónghuàgōngduàn]
熔化工段
英文
melting section-
The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased
本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局部加熱兩個方面進行了優化，結果表明:採用普通工藝焊接時，葉片焊后殘余拉應力出現在焊縫及其附近區域，並且在葉片出水邊的熔合線附近（危險區域）出現了峰值;在採用優化的分段焊時，先焊兩端后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值，降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比，與冷卻面積成反比，並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。Has smelting, rolling, draw bench, heat treatment, becoming products etc. processes and advanced inspection equipments. the scale of our company is expanding because we keep on technology developing, quality full - controlling, strict measuring and reinforcing to internal managements. our company has a stable and large customers group, as well as we do research and development in new products, and we imported the most advanced electro thermal alloy producing technology in the world
上海導達電工合金材料有限公司成立於1998年，經過多年持續不斷的努力，從熔煉軋鋼拉拔熱處理到成材全過程的生產流程及完整的檢測設施，具有規模化的生產量，全面的質量管理，先進的生產工藝及嚴格的檢測手段，使本廠產品保持長久的競爭力，並在不斷的研究開發新產品，產品已通過iso9001質量體系認證， iso14001環保體系人證。Liquid - solid extrusion of composite material is a new kind of metal forming process, which has been developed in recent years with a promising practical application prospect for its simple working procedure, low cost and good workpiece performance. through a lot of experiments, the optimization and chosing method of key process parameters ( pouring temperature, mold warm - up temperature, impregnating pressure, impregnating time ) has been mastered. under the precondition of appropriate chosing these parameters, the effective control of extrusion velocity is the key of mading good workpiece. but the control of extrusion velocity remains a handwork, and it is heavily affected by such uncertainties as a handler ' s knowledge and skill about the process. in order to solve the problem, the automatic control of the extrusion velocity is studied, and a computer control system is also designed under existing condition
通過大量實驗，已掌握了關鍵工藝參數（熔液澆注溫度、擠壓模預熱溫度、浸漬時間、浸漬力）的優化選取方法。在合理選取關鍵工藝參數的前提下，擠壓速度的控制是成形出質量良好製件的關鍵。但是，目前對于擠壓速度的控制仍停留在手動控制階段，利用該工藝制備管、棒材製件的成功與否受操作者對該工藝及其設備的經驗及熟練程度等不確定因素影響很大。
分享友人