熔化端部 的英文怎麼說

中文拼音 [rónghuàduān]
熔化端部 英文
melting end
  • : 動詞(熔化) melt; fuse; smelt
  • : Ⅰ名詞1 (東西的頭) end; extremity 2 (事情的開頭) beginning 3 (門類; 方面) item; point 4 (原...
  • : Ⅰ名詞1 (部分; 部位) part; section; division; region 2 (部門; 機關或組織單位的名稱) unit; mini...
  • 熔化 : melt; smelt; meltdown; fusion; fusation; diatexis; eliquation; run; melting; smelting
  • 端部 : telos
  1. Ultramafic rock fragments, which almost is altered to ophite, distributed in structural zone and displayed structural lens. so far, 9 fragments were discovered and mapped in nujinshan and bujing area ultramafic rock can be divided two kinds according to it ' s geochemical characteristics. one can be correlated with metaperidotite, which represented residual part that primary pyrolite underwent moderate partial melting, from some representative ophiolite melange in the world

    按超鎂鐵巖類的地球學特徵可將其劃分為兩類:一類具有較高而穩定的mgo 、較低的al _ 2o _ 3 、極低的cao , m f值為8 . 0 ? 8 . 4 ,按標準礦物組合進行分類可定為方輝橄欖巖,且均為fa _ ( 100 ) 、 en _ ( 100 )的鎂質元組分;可與世界上一些典型的蛇綠巖套中變質橄欖巖進行對比,代表了原始地幔中等融作用后殘余物。
  2. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的焊接工藝從分段焊和局加熱兩個方面進行了優,結果表明:採用普通工藝焊接時,葉片焊后殘余拉應力出現在焊縫及其附近區域,並且在葉片出水邊的合線附近(危險區域)出現了峰值;在採用優的分段焊時,先焊兩后焊中間的方法可以降低葉片危險區域的焊接殘余拉應力峰值,降低效果與葉片出水邊焊段長度、焊縫各段的焊接方向有關;局加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比,與冷卻面積成反比,並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  3. Surely a telltale hole in the melted wax would expose an end of the metal capsule concealed in the base of the candle

    的蠟燭油中間那個一覽無疑的空洞無疑會露出藏匿在蠟燭根的金屬囊的一
分享友人