熔焊接 的英文怎麼說

中文拼音 [rónghànjiē]
熔焊接 英文
fusion welding
  • : 動詞(熔化) melt; fuse; smelt
  • : 動詞(用熔化的金屬修補金屬器物或使金屬工件連接起來) weld; solder
  • : Ⅰ動詞1 (靠近;接觸) come into contact with; come close to 2 (連接; 使連接) connect; join; put ...
  • 焊接 : weld; welding; soldering; seal; sealing; sealing-in; shutting together
  1. Cell connectors and terminal post burning must be done in such a manner that there is complete fusion of the post strap top and the cover lead bushing with the connector ring or terminal post.

    條和線柱的必須使極柱頂部和蓋子的鉛襯套與連條環口或線柱完全牢固。
  2. Standard reference radiographs for steel fusion welds

    用標準參考射線照片
  3. Method of repeated tension fatigue testing for fusion welded joints

    熔焊接頭重復拉伸疲勞試驗方法
  4. Radiographic examination of fusion welded joints in metallic materials

    金屬頭射線照相
  5. The welding technology of francis turbine runners is optimized from the view of subsection welding and local heating by numerical simulation. the result shows that welding residual tensile stress appears in the weld and its area nearby, and peak stress appears in the dangerous area of blades after practising quondam welding technology ; welding residual tensile peak stress in the dangerous area of blades can be decreased by welding both ends earlier and then welding middle section later during subsection welding, and decreasing effect on welding residual stress of the subsection welding is related to the weld length of blade outlets and welding direction of each subsection ; decreasing effect on residual stress of the local heating is direct proportional to heating time, heating temperature, heating area, and inversely proportional to cooling area, and welding residual tensile peak stress in the dangerous area is decreasing trend earlier, and then increasing trend later with heated location increased

    本文利用數值模擬手段對轉輪的工藝從分段和局部加熱兩個方面進行了優化,結果表明:採用普通工藝時,葉片后殘余拉應力出現在縫及其附近區域,並且在葉片出水邊的合線附近(危險區域)出現了峰值;在採用優化的分段時,先兩端后中間的方法可以降低葉片危險區域的殘余拉應力峰值,降低效果與葉片出水邊段長度、縫各段的方向有關;局部加熱法降低轉輪危險區域殘余應力的效果主要與加熱時間、加熱溫度以及加熱面積成正比,與冷卻面積成反比,並且危險區域的殘余應力隨加熱區域的增大呈先降低后升高的趨勢。
  6. Slag, blowholes, and paint on unfused regions were observed at the welded junctions.

    處看到了夾渣,氣孔及未透區的油漆。
  7. Clamp apparatus for butt welding

    夾具
  8. " ubridge brand " marble mostly to use in slagging powder with drug cover welding electrode. improve slag basicity, steady arc, increase surface strain. it also used on architecture industry

    粵橋牌大理石粉為白色或淺灰色礦粉,主要用於藥皮條等材料的造渣造氣劑,可提高渣堿度穩
  9. Purpose : mainly to be material for making lithium metal and used in making for dehumidizer of air - condition, bleaching powder, disinfestant, electrolyte of lithium - battery, synthetic fiber, welding agent for alloys and flux

    用途:主要用於制取金屬鋰的原料及空調除濕劑、漂白粉、殺蟲劑、鋰電池電解液、合成纖維、合金劑或助劑。
  10. Attachment materials for electronic assembly - requirements for electronic grade solder alloys and fluxed and non - fluxed solid solders for electronic soldering applications

    電子組件用的連材料.電子設備用的電子分級料合金和助劑和非助劑的要求
  11. A new type of joint technique between short _ net copper pipe and soft _ cable connection board, castfusion welding, is introduced. the practice of more than ten years shows that this fusion welding connection has the superiority of higher reliability, simpler processing method, better economy benefit compared to the taper cone face - contacted connection

    介紹了電石爐短網銅管與軟纜線板之間的一種新型連技術? ?澆鑄技術.經過10多年的運行,實踐證明短網銅管與鑄銅軟纜線板的澆鑄,與傳統工藝採用的圓錐面觸連相比較,具有加工工藝簡單、運行可靠性高、經濟效益好等優點
  12. . welding - fusion - welded joints in steel, nickel, titanium and their alloys beam welding excluded - quality levels for imperfections

    .鋼鎳鈦及其合金的熔焊接
  13. Standard specification for electric - fusion - welded steel pipe nps 4 and over

    熔焊接鋼管用標準規范
  14. Visual testing method of fusion - welded joints

    熔焊接頭的目測試驗方法
  15. Destructive tests on welds in metallic materials - longitudinal tensile test on weld metal in fusion welded joints

    金屬材料的破壞試驗.熔焊接點中金屬的縱向拉伸試驗
  16. Destructive tests on welds in metallic materials. longitudinal tensile test on weld metal in fusion welded joints

    金屬材料的破壞性試驗.熔焊接頭上金屬的縱向拉伸試驗
  17. Surface layer welding

    表面熔焊接
  18. Welded hard surfacing

    表面熔焊接
  19. Splices for optical fibres and cables ; part 3 : sectional specification : fusion splices for optical fibres and cables

    光纖和光纜的頭.第3部分:分規范:光纖和光纜的熔焊接
  20. Destructive tests on welds in metallic materials - longitudinal tensile test on weld metal in fusion welded joints ; german version en 876 : 1995

    金屬材料的破壞試驗.有熔焊接頭的金屬的縱向
分享友人