熔爐間 的英文怎麼說
中文拼音 [rónglújiān]
熔爐間
英文
furnace room-
Intermediate frequency furnace ? continuous casting billets ? heated by heating furnace ? rough rolling ? head and tail end cutting ? intermediate rolling ? head and tail cutting ? finish rolling ? water cooling treatment ? multiple - length cutting and dividing ? cooling on the cooling bed ? cutting - to - length by cold shear ? collecting and bundling ? to warehouse
中頻熔爐連續的鑄件鋼坯重復加熱的熔爐粗軋頂端和尾端切斷中間壓軋頂端和尾端切斷完成壓軋水冷處理多功能的長度切割和分段在冷床上冷卻冷卻后冷剪長度聚集捆包運到倉庫。A new type of joint technique between short _ net copper pipe and soft _ cable connection board, castfusion welding, is introduced. the practice of more than ten years shows that this fusion welding connection has the superiority of higher reliability, simpler processing method, better economy benefit compared to the taper cone face - contacted connection
介紹了電石爐短網銅管與軟纜接線板之間的一種新型連接技術? ?澆鑄熔焊技術.經過10多年的運行，實踐證明短網銅管與鑄銅軟纜接線板的澆鑄熔焊連接，與傳統工藝採用的圓錐面接觸連接相比較，具有加工工藝簡單、運行可靠性高、經濟效益好等優點The supreme court, and the constitution, are bulwarks between this country ' s political identity and the bubbling cauldron of world opinion
最高法院和憲法是國家作為一個政治實體和世界觀點的大熔爐之間的壁壘。Abstract : during the heating of scrap with carbon or hydrocarbon contented substances in some process, it will bring problems like explosion of carbon monoxide, fume and smell from oil volatilization, etc. ， if incomplete combustion occurs. through laboratory experiments, the time related variation of gas contents and post combustion ratio of fume during the heating of oil - bearing scrap are studied. the results show that the restrictive chain of reaction procedure is the thermolysis of oil ; that temperature and ( co ) / ( co2 ) ratio influence transformation ratio and post - combustion ratio under lower temperature ; that 900 is the temperature above which the complete reaction can be ensured at all ( co ) / ( co2 ) ratios
文摘:在某些廢鋼熔煉過程中，當爐料中含碳及碳氫物質且燃燒不充分時，會帶來煙氣中一氧化碳的燃爆、油污揮發時造成的煙霧、臭味等問題.通過實驗室裝置研究含油廢鋼在加熱過程中煙氣成分隨時間的改變以及二次燃燒率的變化，試驗結果表明，反應過程的限制性環節是油分的熱分解；在較低的溫度下（ co ） / （ co2 ）比例影響轉化率和二次燃燒率；而在任意比例下保證充分反應的溫度為900以上The results showed that the melting ratio of silica flux decreases and the complete melting time prolongs with the size of silica flux and matte grade increasing, and the effect of the blowing air and oxygen enrichment is not remarkable in the high grade copper matte converting process
對于高品位冰銅轉爐吹煉，鼓入氣體流量和氧濃度對石英熔劑熔化率影響不顯著；熔劑粒度和冰銅品位對熔化率影響顯著，並隨著熔劑粒度和冰銅品位的增加，熔劑熔化率降低，完全熔化時間延長。Additions of carbon for improved slag resistance. spinel formation improves hot strength, slag resistance and brick joint erosion. 3 repairing material for bof uses fused magnesia or sintered magnesia as the main raw material and after modifid pitch and special additives are added, it has the following characteristcs than other conventional converter pitch temperature, shorter sintering time, longer service life and less pollution. it is mainly used for repairing converter working face, also for tapping side, tapping hole and bottom
3 ，轉爐大面補料是採用電熔鎂砂或燒結鎂砂為主要原料，通過加入改性瀝青和特種添加劑使它和傳統瀝青補爐料相比具有高溫附著性好燒結時間短流動性好使用壽命長污染小等特點，主要用於修補轉爐迎鋼面通常稱「大面」也可以用於修補出鋼側，出鋼口及爐底等部位。The performance consistence of ab5 alloy in mass production is influenced by not only the quenching condition, but also the impurities such as fe, mg in mischmetal and the melting technology including the unit output, melting temperature and time, atmosphere, furnace frequency etc
合金性能波動除受澆鑄時的冷卻條件影響外，還與稀土原料中鐵、鎂等雜質及熔煉工藝因素（包括單位產量、熔煉溫度、時間氣氛及爐頻等因素）有關。Abstract : this paper analyses principles for power frequency inductive furnace and power factor parallel compensation and three phases balance, deals with processes of power factor compensation and three phases balance for plc automatic power inductive furnace. for saving source and shortening time of smelting and improving electrice net, they will be of great significance
文摘:分析了工頻感應爐的工作原理、功率因數並聯補償原理和三相平衡原理.論述了plc自動控制工頻爐的功率因數補償、三相平衡的過程.它對節省能源，縮短熔煉時間，改善電網功率因數有重要意義The melting controlling on 3t h two rows distance cold blast cupola
兩排大間距冷風沖天爐的熔煉控制Assume a furnace will require approximately 24, 000 watts after all heat losses and load factors have been considered. increasing this 24, 000 by 25 % to 50 % gives a wattage requirement of between 30, 000 and 36, 000 watts
假定在考慮了熱量散失和負載等因素之後一個熔爐大約需要24000瓦的能量。將這個功率值增加25 %到50 %之後所需的功率在30000瓦到36000瓦之間。Assume a furnace will require approximately 20, 000 watts after all heat losses and load factors have been considered. increasing this 20, 000 by 25 % to 50 % gives a wattage requirement of between 25, 000 and 30, 000 watts
假定在考慮了熱量散失和負載等因素之後一個熔爐大約需要20 ， 000瓦的能量。將這個功率值增加25 %到50 %之後所需的功率在24 ， 000瓦到30 ， 000瓦之間。分享友人