熔融粘度 的英文怎麼說

中文拼音 [róngróngnián]
熔融粘度 英文
melting viscosity
  • : 動詞(熔化) melt; fuse; smelt
  • : Ⅰ動詞1 (融化) melt; thaw 2 (融合; 調和) blend; fuse; be in harmony Ⅱ形容詞[書面語]1 (長遠; ...
  • : 粘動詞(粘附) glue; stick; paste; adhere to; bond
  • : 度動詞[書面語] (推測; 估計) surmise; estimate
  1. Sodium tellurite glasses are considered as potential candidates for non - linear optical applications because of high refractive index values and wide infrared transmittance. on the other hand, because the glasses have relatively low melting temperature and low viscosity after melting, they are often chosen to study the melting, evaporation and solidification of glasses in low gravity

    另一方面,由於這類玻璃的較低,在溫較高時會揮發產生氣體,體的較低,玻璃形成能力強,因此被用來研究微重力下玻璃的化和氣化,和微重力對玻璃析晶能力的影響。
  2. To illustrate the effect of variable feed rate, the pressure and power draw changes with fluctuations in feed rate are calculated on the table below

    瞬間的壓力變化及峰值出現是由熔融粘度瞬間變化導致的。
  3. Viscosity calculating model of iron - bath smelting reduction slag

    鐵浴法還原渣的計算模型
  4. Testing methods for melt viscosity of hot - melt adhesives

    熔融粘度的測定
  5. Instantaneous pressure variations and spikes are due to large instantaneous changes in melt viscosity

    瞬間的壓力變化及峰值出現是由熔融粘度瞬間變化導致的。
  6. At constant temperature, changes in melt viscosity are often due to variable feed rate and / or poor mixing

    恆定時,熔融粘度變化通常是由於投料速率變化和/或混和不均導致的。
  7. For example, a variation of 20 % in the feed rate causes a 9 % increase or decrease in pressure, which is a variability range of 18 %

    恆定時,熔融粘度變化通常是由於投料速率變化和/或混和不均導致的。
  8. Injection time switchover temperature affects the viscosity of the melt, which presents resistance to the advance of the screw

    注射時間轉換溫影響塑料的,而會給螺桿的頂部帶來阻力(反壓力) 。
  9. Second, ptfe composites were treated using different surface treatment methods. the adhesive strength tests were conducted by a standard experiment method. the maximum adhesive strength between ptfe and stainless steel was up to 5. 63 mpa using the melting potassium acetate

    利用不同的表面處理方法對ptfe進行表面改性,然後按標準試驗方法進行接強試驗,結果表明,經過醋酸鉀處理的ptfe與鋼的接強最高,達到5 . 6mpa 。
  10. Exfloited nanocomposites were successfully synthesized. the study of melting compound about pet eva abs pvc cpe and montmorillonite has been carried out. we abtained several intercalated nanocomposites, tem shows the interlayer spacing is no more than 100nm

    首次對pet 、 eva 、 abs 、 pvc 、 cpe 、 pp與蒙脫土復合進行了研究,制得多種插層型納米復合材料, tem照片顯示:多數土片層的厚在100nm以內。
  11. But the degree of modification is less than expectation value. 1n thi s paper a new rnethod, maleic anhydride / styrene dua1 monorners jn - - si tu gm ft - - 1n terca1a tion method, has been introduced successfu11y i n

    近年來有人通過插層的方法來改性pp ,發現pp土插層復合材料( pp claynanocomposites , pcn )的韌性和拉伸強得以同時提高,但並不令人滿意。
分享友人