熔體流動速率 的英文怎麼說

中文拼音 [róngtǐliúdòngsùlǜ]
熔體流動速率 英文
melt flow rate
  • 熔 : 動詞（熔化） melt; fuse; smelt
  • 體 : 體構詞成分。
  • 流 : Ⅰ動1 （液體移動; 流動） flow 2 （移動不定） drift; move; wander 3 （流傳; 傳播） spread 4 （向壞...
  • 速 : Ⅰ形容詞（迅速; 快） fast; rapid; quick; speedy Ⅱ名詞1 （速度） speed; velocity 2 （姓氏） a surna...
  • 率 : 率名詞（比值） rate; ratio; proportion
  • 流動 : 1. （液體或氣體移動） flow; run; circulate 2. （經常變換位置） going from place to place; on the move; mobile
  • 速率 : speed; rate; tempo
  1. The results show a few grooves appear on the worn surface of the composites which contain 10 phr nano - al2o3 there are a great many grooves on the worn surface of the composites containing 20 phr. in addition the deeper cracks also appear. this shows that excess nano - al2o3 particles ca n ' t improve wear properties of pa6 ' s. the proper content of nano - al2o3 in the matrix can enable the molecular chains of pa6 to produce closed joints which resemble the physical crosslinking

    尼龍6 / a12o :復合材料的加工性能研究表明:隨著納米a12o3的加入，復合材料的熔體流動速率下降，納米a12o3含量越大，下降越明顯，即隊6 / a12o3納米復合材料的加工性能越差;隨著納米a12o3的加入，復合材料的轉矩和塑化時間都增加，當含量小於巧phr時，隊6復合材料的轉矩增加幅度不大，當含量超過15phr后，轉矩急劇升高。
  2. Verification regulation of extrusion plastometer

    熔體流動速率儀檢定規程
  3. The analysis of ir spectrum and melt flow index showed that the composite had a micro - crosslinking structure, and the analysis of dsc discovered there was - spherulite in the aggregate structure of the composite of pp

    紅外光譜分析和熔體質量流動速率的測定表明，復合材料體系產生了微交聯； dsc分析發現， pp材料的聚集態結構中含有球晶。
  4. Electron type omnipotent testing machine cmt5504, hot to link card appearance xwb - 300a, pulling force testing machine lj1000, melting body flow speed appearance xrz400, simple to prop up roof beam strike testing machine xjj - 50j, etc

    、電子式萬能試驗機cmt5504 、熱變形維卡儀xwb - 300a 、拉力試驗機lj1000 、熔體流動速率儀xrz400 、簡支梁沖擊試驗機xjj - 50j等
  5. Servo control computer system / microcomputer universal testing machines, ozone tester, compression flexometer, computer hdt / vicat tester, digital impact tester, melt flow indexer, moving die rheometer, mooney viscometer, lamination of pvc plastic press tester

    伺服控制電腦系統微電腦式拉力試驗機，耐臭氧機，橡膠壓縮生熱試驗機，塑料用維卡熱變形，數位沖擊試驗機，塑膠熔體流動速率機，無轉子密閉膜腔硫化儀，門尼黏度試驗機等等。
  6. The result of analysis shows that the convective heat flux has main effect on fuel pyrolyzing and vaporizing, the liquid layer of pe fuel can increase the regression rate but also can cause unstable burning. 4

    研究結果表明：對流熱流是引起燃料熱解氣化的主要因素， pe熔化產生的液體層提高了燃料熱解退移速率，但液體層厚度增加到一定程度時，對發動機工作穩定性有負面影響。
  7. Determination of the melt mass - flow rate and the melt volume - flow rate of thermoplastics

    熱塑性塑料熔體質量流動速率和熔體體積流動速率的測定
  8. Polyethylene pipes and fittings - determination ofmelt flow rate

    熔體流動速率試驗方法
  9. Specifications for the melt flow ratemeters

    熔體流動速率儀.技術條件
  10. Al these can increase the nucleation rate, so the tic particles become smaller and disperse more homogeneous, and the volume fraction of tic is increased. when 0. 5wt % rare earth ceo2 is added to melt, the surface tension of melt is decreased and fluidity is enhanced, accordingly it enhances the diffusion rate of ti to c particles during the course of reaction and prompts the formation of tic

    加入0 . 5wt的稀土ceo _ 2增大了熔體的表面張力及流動性，從而在反應階段增大ti原子朝c顆粒的擴散速率，促使tic顆粒生成，以及在反應完成後增大tic顆粒朝熔體中擴散的速率，促使tic顆粒的形核。
  11. Polyethylene pipes and fittings - designation of polyethylene based on nominal density and melt flow rate

    根據聚乙烯公稱密度和熔體流動速率命名的方法
分享友人
分享到 Line

分享到臉書