熱力蠕變 的英文怎麼說

中文拼音 [rèlìrúbiàn]
熱力蠕變 英文
thermal creep
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 蠕 : 動詞（蠕動） wriggle; squirm
  • 熱力 : [機械工程] heating power
  1. The proper interpass temperature is required to prevent cold and hot cracking as well as the proper selection of welding filler material, to produce the proper creep resistance and toughness

    需要適當的程間溫度和正確選擇填充金屬材料來防止冷熱裂縫，產生適當的蠕變阻力和韌性。
  2. It is the first time to use the conventional espi system ( neither phase shifting nor carrier is used ) to continuously analyze the super low frequency vibration with high quantitative in the world

    在火箭固體燃料動態力學特性研究中，時間序列法成功的給出了固體燃料的蠕變曲線和蠕變速率曲線，並且給出了其熱變形和蠕變不同時刻的全場位移分佈。
  3. The combustor do n ' t fail if transient rise of temperature field is neglected, the stress field of combustor can n ' t cause gas film wall rupture. 2. combustor ' s creep and relaxation is calculated in steady temperature field, the results show that creep and relaxation is not main reason destroying combustor chamber

    對穩態溫度場下的蠕變鬆弛計算表明，高溫下的蠕變鬆弛促使火焰筒的熱應力下降，在所考慮的條件下穩態溫度場導致火焰筒的蠕變變形不是火焰筒破壞的主要原因。
  4. So far, many studies on general properties of 3d - c / sic have been carried out, but the study on its interaction fatigue - creep and thermal shock behavior, especially at high temperature, has not been reported

    文獻中對其常規力學性能研究較多，而對其熱震和疲勞蠕變交互作用行為鮮見報道。
  5. Thermal insulating products for building applications - determination of compressive creep ; german version en 1606 : 1994

    建築用絕熱材料.壓力蠕變測定
  6. Third, the mechanical properties were conducted by tensile test, and analyzed the relationship between the length, content, coupling agent levels and the tensile strength, tensile modulus of composites films. the result showed that the optimum formulation was the contents of long milled glass fiber 20. 0wt % and coupling agent kh - 550 1. 0wt %

    最後，利用動態力學分析（ dma ）和差示掃描量熱儀（ dsc ）對所制備的應變片基底材料進行了熱學性能測試，得到了材料的玻璃化轉變溫度tg 、蠕變和應變回復率。
  7. Evaluation of creep deformation property by the laser thermal stress method

    基於激光熱應力法的薄膜蠕變性能評估方法
  8. The larson - miller method and the superheater wall temperature computation model brought forward by soviet criterion are adopted to calculate the life loss caused by creep. and a simplification formula is put forward to apply in the on - line life inspection system

    本文採用拉森米勒參數法，結合前蘇聯1973年熱力計算標準中的過熱器壁溫計算模型，對前期蠕變壽命損耗進行了計算；並提出簡化方法，用於在線壽命監測系統中。
  9. If the downstream system pressure is higher than the set pressure under no flow conditions, the cause could be thermal expansion, pressure creep or dirt / debris on the seat

    如果在無流量情況下，下游系統壓力高於設置壓力，則原因可能是熱膨脹，壓力蠕變或閥座上的污垢/碎片。
分享友人
分享到 Line

分享到臉書