熱壓制團的英文怎麼說

中文拼音 [zhìtuán]
熱壓制團英文
hot briquetting

  • : 壓構詞成分。
  • : Ⅰ動詞1 (製造) make; manufacture 2 (擬訂; 規定) draw up; establish 3 (用強力約束; 限定; 管束...
  • : Ⅰ名詞1 (團子) dumpling 2 (成球形的東西) sth shaped like a ball 3 (工作或活動的集體) group; ...

※中文詞彙熱壓制團在字典百科國語字典中的解釋。

  1. Thus, the defensive unit stays secure ( mentality + pressing + d - line ) and keeps the ball rather than playing risky forward passes ( mentality )

    這樣,防守體就能保證穩固(心態的設置++防線深拉) ,控球在腳,不冒險向前傳球(通過心態設置) 。
  2. Sicp / al matrix composites, with 5, 15 and 25 % volume fraction of sic particles, were prepared by vacuum hot - pressing sintering processing in this paper. based on mechanics properties, sem observation and energy dispersive x - ray analysis, the interface reaction phenomenon of sicp / al composites made by vacuum hot - pressing sintering, as well as the reinforcement and fracture mechanisms of this composite were analyzed. the dynamic responses of sipc / al composites were studied by a split hopkinson high - speed pressure bar impact system which strain rate was from quasistatic state strain rate ( 3. 3 10 - 3s - 1 ) to dynamic state strain rate ( 5. 2 103 s - 1 )

    本研究以武裝直升飛機防護裝甲材料為研究對象,採用真空粉末冶金燒結工藝備了含sic顆粒體積分數分別為5 、 15和25的sic顆粒增強鋁基復合材料,結合其力學性能、掃描電鏡和界面微區能譜分析結果,分析了sic _ p al復合材料的真空燒結過程中的界面現象,以及材料增強和斷裂機理,並利用hopkinson高速桿沖擊實驗系統對其從靜態到動態(應變率為3 . 3 10 ~ ( - 3 ) s ~ ( - 1 ) 5 . 2 10 ~ 3s ~ ( - 1 ) )的縮破壞響應進行了研究,分析了不同體積分數sic _ p al復合材料高應變率縮載荷下,材料的變形和微觀損傷機理,以及利用高速沖擊空氣炮測定了改復合材料備剃度復合板的穿透性能。
  3. The siloviki have shown they can squash opposition, suborn the courts and stay in charge

    「西羅維基」集表明了他們能夠反對意見,收買法庭和掌控一切。
  4. The age hardening characteristic of as - cast cu20ni20mn and cu20ni35mn alloys and the interface characteristic between the alloy and cast tungsten carbide were studied, and on the basis of this study, composites of cu - ni - mn alloy reinforced with different volume fraction ( 0 - 45vol. % ) and different size ( 42 - 362 m ) of cast tungsten carbide particles were made by vacuum hot - pressing liquid sintering technology. pin on disk two body abrasion tests have been performed with different size of sic abrasive under different loads

    本文研究了鑄態cu20ni20mn和cu20ni35mn合金的時效硬化特性及其與鑄造碳化鎢的界面特性,並在此基礎上以不同尺寸( 42 362 m )的鑄造碳化鎢顆粒為增強體,採用真空液相燒結技術備了不同顆粒含量( 0 45vol . )的鑄造碳化鎢顆粒增強cu - ni - mn合金基復合材料;以不同粒度的sic為磨料,在不同載荷條件下利用銷?盤磨損試驗機測試了復合材料的二體磨料磨損性能。
  5. The disperse degree of the ceramic can greatly affect uniformity of the composite, which limit the poling voltage and affect the piezoelectricity. in this paper, the relationships among constitutes, microstructures, dielectric and piezoelectric properties were calculated by employing the banno unit cell mode ; pzt ceramic were synthesized by the hydrothermal method and the appropriate solution was selected according the adsorption of pvdf on the ceramic particle surface ; then, relationships between the disperse degree and the fabrication process were studied. base on these, the pzt / pvdf composites intermingled some pan were prepared and the microstructures were investigated

    論文首先利用bannounitcell模型,計算了pzt pvdf電復合材料的組成、結構、與其電和介電等性能之間的關系;針對電復合材料存在的均勻分散性差的缺點,選用水備的粒度均勻的pzt陶瓷粉末,並採用溶液混和法與聚合物pvdf進行分散復合,重點研究了不同工藝條件下陶瓷的均勻分散性及其與材料微觀結構之間的關系。
分享友人