熱壓燒結 的英文怎麼說

中文拼音 [rèyāshāojiē]
熱壓燒結 英文
hot pressed sintering
  • 壓 : 壓構詞成分。
  • 燒 : Ⅰ動詞1 （使東西著火） burn 2 （加熱或接觸某些化學藥品、放射性物質等使物體起變化） cook; bake; hea...
  • 結 : 結動詞（長出果實或種子） bear （fruit）; form （seed）
  1. This thesis reports some results on the hot press sintering of nano - composite wc - co powder, which is prepared by spray pyrogenation & continuous deoxidization and carbonization process

    本課題採用熱壓燒結技術對以噴霧熱解?連續還原碳化法制備的納米復合wc - co粉末進行了熱壓燒結研究。
  2. In chapter two, we fabricated r - ni - fe / al2o3 nanocomposites successfully by using ball - milling mixing method plus hot - pressing process. meanwhile, their microstructures are characterized by x - ray diffraction ( xrd ) analyser, transmission electron microscopy ( tem ), field emission scanning electron microscopy ( fe - sem ) and brunauer - emmett - teller ( bet ). the results indicate that ni - fe particles are homogenously dispersed in the matrix in the composites

    在第二章中，我們採用高能球磨混合方法加上熱壓燒結工藝，成功制備了ni - 20fe al _ 2o _ 3納米復合材料，並通過x射線衍射儀（ xrd ） 、透射電鏡（ tem ） 、場發射掃描電鏡（ fe - sem ） 、比表面孔隙儀（ bet ）對該復合材料的微結構進行了表徵。
  3. Analyzing the influence factors for the performance of diamond drill bit in hot pressure sintering process of intermediate - frequency furnace

    淺析中頻熱壓燒結過程中影響金剛石鉆頭性能的因素
  4. In this paper, nanosized al2o3 ceramic particles were chose as reinforcing phase. enhanced with ultrasonic wave the particles were covered with copper using method by electroless plating, the copper - matrix composite was developed by hot - press sintering process of the composite powder. the composition, microstructure, hardness, density and dry sliding wear property of the new material have been studied

    研究路線為：選用納米級al _ 2o _ 3陶瓷顆粒作為增強相，在超聲波的環境中用化學鍍的方法完成對納米al _ 2o _ 3陶瓷顆粒表面的金屬銅包覆，採用熱壓燒結成型技術以復合粉末為原料制備成納米al _ 2o _ 3陶瓷顆粒增強銅基復合材料，研究分析復合材料的成分、組織結構、硬度以及緻密度，對試樣進行了干滑動摩擦磨損實驗。
  5. Based on nanometer powders, cajc cvbased oxides were synthesized by constant sintering, cold isostate pressure and hot pressure methods. it can be found that sintering methods have a great influence on thermoelectric performances : the sample synthesized by hot pressure method is most dense and has the best thermoelectric performances. the microstructures and thermoelectric properties of cascog - based oxides doped by four dopants have been investigated

    採用不同的后續工藝制備最終的熱電材料，研究不同工藝對熱電性能的影響發現：熱壓燒結制備出的熱電材料最緻密，其熱電性能也最好；先冷等靜壓成型后常壓燒結方法次之；直接常壓燒結法燒出的樣品氣孔最多，性能也最差。
  6. In this article, by rf sputtering the licoo _ 2 film was produced. by hot pressing and cold pressing ( and sintering ), the licoo _ 2 targets used in the rf sputtering were produced differently. both technics of the preparation of the licoo _ 2 film and the licoo _ 2 target were studied

    本文使用熱壓燒結方法和冷壓后燒結方法制備了磁控濺射用的licoo _ 2靶材，並使用磁控濺射方法制備了licoo _ 2薄膜，對兩者的制備工藝進行了研究。
  7. Hot - pressing sintering of w - 15cu alloy

    熱壓燒結制備高密度鎢銅合金
  8. The results indicate that arc melting is a good method to produce nb - si system intermetallics due to its simpler technics, lower cost and compact products. however, powder metallurgy is found to be not suitable to produce the nb - si system intermetallics due to its coarse and loose products resulting from the poor molding property of nb and si mixed powders. optical floating zone technology, which is used to fabricate nb - si intermetallic composites for the first time, is also found to be a good way to produce nb - si system intermetallics because of its compact products and good property despite of its relatively high cost

    結果表明，電弧熔煉方法制備得到的nb - si系金屬間化合物比較緻密，且制備工藝簡單，經濟實用，是一種合適的nb - si系金屬間化合物制備方法；由於nb 、 si元素粉末的成型性很差，用粉末冶金方法（熱壓燒結和冷等靜壓）制備的nb - si系金屬間化合物表面粗糙、緻密度低，且成本較高，不宜用於制備nb - si系金屬間化合物；首次用光學懸浮單晶生長技術制備的nb - si系金屬間化合物復合材料緻密度很高，盡管成本稍高，但由於性能最佳，也是一種合適的nb - si系金屬間化合物制備方法。
  9. The multilayer composite including a hard component tz - 3y20a and a plastic soft component mo has been fabricated by particle sedimentation method. by choosing appropriate settling parameters and dispersed medium, the tz - 3y20a / mo multilayer composite has been obtained via alternating deposition of tz - 3y20a and mo according to the design of individual layer thickness and layer thickness " ratio

    採用顆粒沉降成型工藝，選用適當的沉降參數與分散介質，將tz - 3y20a陶瓷粉和mo金屬粉按設計的層厚和層數進行交互沉降，得到預成型體，再經1500 ? 20mpa ? 1h熱壓燒結，制備出緻密的tz - 3y20a mo疊層材料。
  10. In this thesis adding the pre - process carbon nanotubes into the powder of silicon nitride, with ball milling, drying and sieving, fabricate the silicon nitride ceramics applying the hp sintering method, which in order to improve the toughness of the silicon nitride

    本文就是利用碳納米管優良的力學性能，在對其預處理后，將其添加到氮化硅陶瓷粉末中，經球磨、乾燥、過篩后，採用熱壓燒結工藝，制備氮化硅陶瓷，以期改善氮化硅陶瓷的韌性。
  11. Using aluminium sulfate and colloidal silica as raw materials, another kind of mullite precursor powders is made. the relative density of silica - rich mullite ceramic sintered from these powders at 1550 for 1 hour with a pressure of 15mpa is 97 %

    以硫酸鋁、硅溶膠為原料，採用溶膠-凝膠法制備了莫來石先驅體粉末，所得富硅莫來石先驅體粉末在1550 、 15mpa下熱壓燒結1小時后，緻密度達97 。
  12. The dielectric constants of silica - rich, alumina - rich, and stoichiometric mullite ceramics are 5. 5, 6. 0 and 6. 3 respectively. the dielectric constant of mullite - si / c / n composites is related with the sintering parameters. with the increase of the sintering temperature and dwelling time, the " " and tg of mullite - si / c / n composites are decreased, this phenomenon is related with the change of the microstructure and phase composition of nano si / c / n powders

    莫來石- si c n復合材料的介電常數與熱壓燒結工藝有很大的關系，隨熱壓燒結溫度（ 1450 1600之間）的升高，燒結時間（燒結溫度為1550 ）的增長，莫來石- si c n復合材料的介電常數實部、虛部及介電損耗角正切均明顯下降，這與吸收劑的性質隨溫度和時間的變化有關。
  13. The experimental techniques ( such as sedimentation equipment, controlling the size and size distribution of powders, the concentration of suspension ) have been devised subtly. on the basis of theoretical and densification design, the w - mo - ti fgm has been obtained by particle settling and hot pressing sintering. the structures of specimen were observed by electron probe

    通過對實驗工藝，如沉降設備、原料粒度及粒度分佈的控制、懸浮液濃度等方面進行精細的設計，在理論設計和緻密化研究的基礎上，通過顆粒共沉降得到梯度沉積體，並通過真空熱壓燒結得到w - mo - ti功能梯度材料。
  14. Differential thermal analysis ( dta ) of starting powers and x - ray diffraction ( xrd ) of samples sintered at different temperatures from 600 c to 1300 c by hot pressing were utilized to analyse the phase composition

    採用原位熱壓燒結工藝，通過差熱分析和x衍射圖譜，分析了600 1300不同燒結溫度下燒結所得產物的相組成。
  15. The foundation to develop nb - si system intermetallics base high temperature structure materials has also been established in some degree in this paper. arc melting, powder metallurgy and optical floating zone technology have been used and compared to fabricate the nb - si system intermetallics

    運用電弧熔煉、粉末冶金熱壓燒結、粉末冶金冷等靜壓和光學懸浮單晶生長技術等方法制備了nb - si系金屬間化合物，並對這四種方法制備的nb - si系金屬間化合物進行了比較。
  16. The sintering time also affects the specimens " properties. nano - composite wc - co powder can be hot press sintered to cermet whose hra is 94. 6 and trs is 1183 mpa under 1350 for 2 hours

    最終燒結實驗表明納米復合wc - co粉末1350保溫2小時條件下的熱壓燒結可以獲得抗彎強度為1183mpa ，洛氏硬度為94 . 6的硬質合金。
  17. The la1 - xsrxmno3 powder has been sintered by constant pressure sintering, heat pressure sintering ( hp ) and spark plasma sintering ( sps )

    通過無壓燒結，熱壓燒結和sps燒結工藝對lal . xsrxmno3粉末進行燒結，其中sps燒結在900 ，保溫1omin得到的燒結樣品緻密化程度最好。
  18. In this paper, ti3sic2 material and ti3sic2 / sic composites, which were fabricated by non - pressing sintered and hot - pressing sintered methods are mentioned and the effects of the synthesis conditions on the phase composition, microstructure and mechanical properties were investigated

    本文通過無壓真空燒結和熱壓燒結制備了ti _ 3sic _ 2材料和ti _ 3sic _ 2 sic復合材料，研究了工藝制度對復合材料物相組成、顯微結構和力學性能的影響。
  19. The physical properties and high temperature oxidation resistance of the ti3sic2 samples were studied

    研究了熱壓燒結ti _ 3sic _ 2的物理性能和高溫抗氧化性能。
  20. Considering the growing of nano - sized powder during sintering and to improve the physical performance, some sintering research about the addition of inhibitor vc has been done

    針對納米粉末在燒結中容易長大的特點，也為了改善材料的物理性能，對添加抑晶劑vc的原料粉末的熱壓燒結進行了一些研究。
分享友人
分享到 Line

分享到臉書