熱效壓力表 的英文怎麼說

中文拼音 [rèxiàoyālìbiǎo]
熱效壓力表 英文
hot-wire manometer
  • 效 : Ⅰ名詞（效果; 功用） effect; efficiency; result Ⅱ動詞1 （仿效） imitate; follow the example of 2 ...
  • 壓 : 壓構詞成分。
  • 力 : Ⅰ名1 （力量; 能力） power; strength; ability; capacity 2 [物理學] （改變物體運動狀態的作用） forc...
  • 表 : Ⅰ名詞1 （外面;外表） outside; surface; external 2 （中表親戚） the relationship between the child...
  1. Through the special studies on impacts to atomizing and humidifying effect from such factors as the firing pin type, centrifugal structure, higher spraying pressure, less aperture, initial water temperature and original state of the air, some conclusions are obtained, such as : the centrifugal nozzle with firing pin type, high pressure and little aperture has bigger air eddy and atomizing angle. the spaying liquid has high velocity. the droplet is small, and the heat and mass transfer velocity is high

    通過對撞針型結構、離心式結構、較高的噴水壓力、較小的噴嘴孔徑、噴水初溫及待加濕空氣初狀態對霧化加濕效果的作用原理的重點分析，得到：撞針型高壓小孔徑離心式噴嘴具有較大的空氣渦與霧化角，噴出的液體流速高、液滴小、水與空氣傳熱傳質速率高，撞針型結構提高了霧化加濕效率，高壓小孔徑的特點為霧化加濕提供了較大的能量，而噴水初溫的升高會減小水的粘性力和表面張力，從而優化加濕效果。
  2. The investigation of a lot of parameters about treated sandstone, brick materials and earthen materials with fluorited polymers has been carried out, such as the formation of polymer, the penetration depth, porosity, capillary absorption and penetration coefficient, water uptake, compressive strength, drilling resistance, absorption isotherms of water vapor, water vapor diffusion, color changes as well as resistance to desegregation of water, frizzing - throwing cycles, worming - cooling cycles, and so on. in addition, the influence of salt crystallization, acid and base, and uv aging have also been assessed in order to better understand the protection effects and utilization possibility of two fluorinated polymers, mainly according to astm standard and the combination of international methods together with general technological

    分別以國家級文物保護單位的土質、砂巖和磚材文物樣品為對象，依據astm標準及國際通用文物保護研究方法與評估準則相結合，通過膠化物形成周期、滲透深度、孔隙度、毛細吸水和滲透系數、持水量、抗壓強度、抗鉆強度、吸附水蒸氣的能力、透氣性、外觀顏色等系列參數的測定，及凍融、冷熱循環、酸堿腐蝕后抗壓強度的衰減、可溶鹽對保護效果的影響、酸堿及光照對表面保護效果的影響，對兩種含氟聚合物及其與有機硅的共混物在文物加固保護和表面防護中的可行性和保護效果給予了系統研究。
  3. The subject for different process technology and surface treatment of crank takes tracking checkout for its internal stress, analyses relation of jumping measurement, deformation measurement, recovery measurement and stress change, finds the reason and usual law of jumping overproof of crank. through cold pressure alignment, hot pressure alignment, support aged alignment and so on methods for 42crmo steel crank, the subject checks change of stress in the process of alignment and change of tissue and property after alignment for crank, and gives comprehensive evaluation for every alignment technology, then give safe and feasible technology parameter

    本課題主要是對不同加工工藝及不同表面處理過程的曲軸，對其內應力進行跟蹤檢測，分析各工藝過程中跳動量、變形量、恢復量與應力改變的關系，找出曲軸跳動量超差的原因和一般規律。通過對42crmo鋼曲軸進行「常溫壓力校直」 、 「熱壓力校直」 、 「支撐時效校直」等方法的校直，檢測校直過程中曲軸應力的變化及校直后組織和性能的改變，進而對各校直工藝進行綜合評價，給出安全可行的工藝參數。
  4. The results indicated that, the fabrication process of ultra - fine grain material is mainly determined by the stress, rotate speed and the flux of cooling water. the grain refining and the hardening effect are mostly affected by the rotate speed and the flux of cooling water. compared with commercial ly12, the invalidate strength and the prolongation rate of the ultra - fine grain material are properly improved in the measurement of compression property ; and the abrupt change of the dilatability of the ultra - fine grain material at 500c is found ; also the phenomena of which the grain size of these microstructures is stable when annealed under 300c is observed

    研究表明，採用本文提出的摩擦壓扭強變形區轉移法可以得到棒狀的超細晶材料，軸向壓力、扭轉速度和溫度是採用該方法制備超細晶材料的主控參數；試件的旋轉轉速和冷卻速度對變形區晶粒細化和硬化效果影響顯著；超細晶ly12的壓縮性能與淬火+自然時效狀態的ly12壓縮性能相比，斷裂強度和延伸率均有一定程度的增強；超細晶ly12的熱膨脹系數在550左右發生明顯的變化。
  5. The blade inner channel cooling is a complex convection - conduction coupling problem. this thesis build a three - dimension. compressible turbulence model, and give a general solve method. with the geometrical model of the glossily rectangle straight channel, the rectangle straight channel with in - line arrays disturb plates, the rectangle straight channel with staggered arrays disturb plates, the rectangle straight channel with slant disturb plates, this thesis compute the flow and heat transfer condition when the cold air path though these channels, and gain the temperature field, pressure field, velocity filed, in addition. this thesis also analyze the influence of the different channel height, the different channel materials, the different channels, and gain the function relation between he nusselt number, friction factor and reynolds number. this thesis is emphasis on the new heat transfer enhancement structure, that is, disturb plates, with the comparison with the glossily channel and channel with pin fins, the heat transfer enhancement effect of the former is better, and the conclusion can be used in the design of aircraft blade

    葉片內部通道冷卻是一個復雜的對流?導熱耦合傳熱問題，本文在分析葉片內部通道冷卻的流動與傳熱情況的基礎上，建立了三維、可壓縮紊流的物理模型，得到了通用的求解辦法；利用不帶擾流片的矩形直通道、帶順排擾流片矩形直通道、帶叉排擾流片、帶傾斜擾流片的矩形直通道的幾何模型，計算了冷卻空氣通過這幾種通道時的流動與換熱情況，得到了各種不同情況下計算區域的溫度場、壓力場、速度場；在此基礎上分析了不同的通道高度、不同的葉片通道材質對葉片內部通道冷卻的影響，並整理得到了各種通道形式下，努謝爾數和阻力因子與雷諾數的函數關系；本文重點研究了新型的葉片內部通道冷卻強化傳熱措施?帶擾流片的內部冷卻通道的強化傳熱效果，通過與光滑矩形直通道、帶針肋通道的冷卻效果的比較，表明了這種新型鮚構的優勢，對于葉片內部通道冷卻結構的設計可以起到指導的作用。
  6. Based on the hydrodynamic energy transport model, the influence of variation of negative junction depth caused by concave depth on the characteristics of deep - sub - micron pmosfet has been studied. the results are explained by the interior physical mechanism and compared with that caused by the source / drain depth. research results indicate that with the increase of negative junction depth ( due to the increase of groove depth ), the threshold voltage increases, the sub - threshold characteristics and the drain current driving capability degrade, and the hot carrier immunity becomes better in deep - sub - micron pmosfet. the short - channel - effect suppression and hot - carrier - effect immunity are better, while the degradation of drain current driving ability is smaller than those with the increase of depth of negative junction caused by source / drain junction shallow. so the variation of concave depth is of great advantage to improve the characteristics of grooved - gate mosfet

    基於能量輸運模型對由凹槽深度改變引起的負結深的變化對深亞微米槽柵pmosfet性能的影響進行了分析，對所得結果從器件內部物理機制上進行了討論，最後與由漏源結深變化導致的負結深的改變對器件特性的影響進行了對比.研究結果表明隨著負結深（凹槽深度）的增大，槽柵器件的閾值電壓升高，亞閾斜率退化，漏極驅動能力減弱，器件短溝道效應的抑制更為有效，抗熱載流子性能的提高較大，且器件的漏極驅動能力的退化要比改變結深小.因此，改變槽深加大負結深更有利於器件性能的提高
  7. The results show that the heat transfer in intake manifold and cylinder has obvious effects on the volume efficiency, while the pipe friction coefficients and bent pressure loss coefficients have less effect

    結果表明，進氣管和氣缸的傳熱對充氣效率的影響較顯著，而管道摩擦系數和彎管壓力損失系數對充氣效率的影響較小。
  8. Through analyzing the effect of temperature and nitrogen on crude oil viscosity the influences of different nitrogen injection volume and injection modes on steam displacement are contrasted, the mechanism of nitrogen - assisted steam stimulation is clarified, which includes : heat carrying capacity is raised, the saturation of remaining oil is reduced after nitrogen - assisted injection is made ; crude oil flow is enhanced because of nitrogen compression and dispersion and the change of oil flow shape ; water back - production rate is improved by expanding the steam sweep volume and compensating in - situ energy ; steam distillation effect is enhanced

    通過分析溫度、氮氣對原油粘度的影響，對比不同注氮量、不同注入方式等對蒸汽驅油效果的影響，弄清了氮氣輔助蒸汽增產的機理主要表現在：氮氣輔助后增加攜熱能力，降低殘余油飽和度，氮氣的壓縮膨脹作用分散和改變了原油流動形態，增強了原油流動性；擴大蒸汽的波及體積，補充地層能量，提高回採水率，強化蒸汽蒸餾效應。
  9. The results indicates that the cubic logarithm polynomials can accurately reconstruct the raw thermal images in the experiment, and can effectively suppress the interference to defect recognition caused by random noise and uneven heating in the pt testing of composite laminates ; the digital images from data reconstruction have clearer defect display or higher defect resolution than the raw thermal images, and the quadratic coefficient image of cubic logarithm regression shows the highest snr

    結果表明利用三次對數多項式回歸即可精確地重建本次實驗的原始熱像，同時能有效地克服復合材料層壓板脈沖熱像檢測中隨機噪聲和加熱不均效應對缺陷識別的干擾；經過數據重建后所作的數字圖像比原始熱像有更高的缺陷顯示度或分辨力，其中以三次對數多項式回歸公式中的二次項系數所作的數字圖像的信噪比最大。
  10. Recent years, the using of piezoelectric sensors becomes a focus in novel biosensors research. the basic principle is that the characters of its oscillation are highly responded with the changes of the surface mass adsorption, or the physic characters in the reaction system including density, viscosity, conductivity and so on. a piezoelectric biosensor with a nanogram sensitivity could be constructed through a reasonable biological processing and structure designing to the piezoelectric quartz crystal

    近年來，壓電傳感器檢測技術逐漸成為生物分析中的研究熱點，其基本原理是利用石英晶體振蕩特性對石英晶體表面質量負載（質量效應）和反應體系物理性狀如密度、粘度、電導率（非質量效應）等的改變具有高度敏感的特性，通過對石英晶體進行適當的生物學處理和結構設計，構建出具有具有ng級檢測能力的生物傳感器。
  11. In the second chapter, firstly, based on the analysis of theoretic cycle of hydrogen engine, the relations between state parameters in four strokes are established

    以氫燃料發動機的理論循環為基礎，進行了各工作過程狀態參數的計算分析，得出了描述理論循環動力性和經濟性，即平均指示壓力和熱效率的表達式。
  12. The results show that : the lose of pressure is small when air velocity and the longth of honeycomb potter heat storage bed are varied ; but the switch time of air and the bulk of storage bed play important roles as regard its dynamic thermal performance

    結果表明：蜂窩型陶瓷蓄熱體換熱器的壓力損失隨著空氣流速以及蓄熱體長度的不同而變化，但總體上說，其壓力損失並不大；四通換向閥的換向周期和蜂窩陶瓷蓄熱體換熱器的體積等是影響其溫度效率和熱回收率等熱性能的重要因素。
  13. Mr wu said that the new hotline is meant to give staff and their families a support network and help them stay well adjusted and positive in the face of pressure and adversities. shkp is also planning to set up a team of lay staff counsellors, who will receive basic training and then help colleagues deal with stress in the workplace

    鬍子翔表示，熱線服務同時惠及員工及其配偶子女是很新的嘗試，希望藉此助員工建立良好的支援網，務求工作與家庭之間互相配合，達致維持心理健康質素的最佳效果，當遇到壓力及逆境時有更強大的正面能量應付。
  14. ( 3 ) the most principal factors that influence the supersonic atomization process include the flow ratio of the gas - liquid metal ( gmr ) value, the flow of atomizing of gas and the range of the inverse vortex taper. the more of the value of three factors, the more advantage they are for the atomization and the more fine the powders are. ( 4 ) the produced powders are the best in efficient atomization efficiency, particle diameter, particle shape and dispersion when the solder alloy is zhl63a, atomizing medium is n2, the protrusion h = 6. 0mm, atomizing gas pressure p = 100mpa, over - heat temperature t = 167 ( t = 350 )

    研究結果表明： （ 1 ）超音速霧化器的氣體流場在導液管下端形成一個倒渦流錐，在二維空間上呈軸對稱的雙峰分佈，負壓形成於這個倒渦流錐內； （ 2 ）修正後的霧化氣體速度公式可以滿足超音速霧化的要求； （ 3 ）影響超音速霧化工藝最根本的因素有氣液質量流率比（ gmr ）的大小、霧化氣體流量和倒渦流錐范圍，三個因素的值越大，對形成細粉越有利； （ 4 ）在焊錫合金為zhl63a ，霧化介質微n _ 2 ，導液管突出高度取h = 6 . 0mm ，霧化氣體壓力取p = 1 . 0mpa ，合金過熱度取t = 167 （ t = 350 ）時，所制得的粉末在有效霧化率、顆粒球形度、粒度及其離散度三個方面綜合性能最好。
  15. The heat transfer enhancement is different under different oscillator. there is the optimum oscillation intensity under which the heat transfer coefficient will be increased by about 30 percent. the change of outlet structure size of a resonance chamber shows little effect on the strength of heat transfer : the pressure of the optional heat transfer coefficient always is between 0. 4mpa and 0. 6mpa, and the optional heat transfer coefficient is enhanced by 30 percent or so

    不同的振蕩強度，強化換熱的效果也不同，存在一個最佳強度，此時的強化換熱效果最好，可以將表面換熱系數提高30 %左右；對于同一共振腔，配合以不同的出口結構尺寸，對于換熱效果的強化的影響變化不大：出現最佳強化效果時的壓力基本都在0 . 4 - 0 . 6 ，最佳的強化效果也都是將表面換熱系數提高30 %左右。
  16. The research results show that the counter - flow condensers have a better performance than that of other arrangements in single - circuit condensers, and that branch flow should be adopted in multi - rows condensers to decrease the pressure drop and increase the heat transfer capacity, and that the influence of gravity force can not be ignored, and that there must be an optimum refrigerant mass flow which can make the condenser perform best when the air velocity is constant while there must be an optimum air flow which can make the condenser perform best when the refrigerant mass flow is constant

    研究結果表明，單迴路冷凝器中，逆流布置換熱效果最好，叉流其次，順流最差；多排管冷凝器應盡可能採用分流方式，以減小壓降，增強換熱；布置冷凝器流程時，重力的影響不可忽略；當風量不變時，必然存在一最佳製冷劑流量使冷凝器性能達到最佳；當製冷劑流量保持不變時，也相應存在一個最佳風量使冷凝器性能最佳。
  17. A parameter has been defined to account for both the heat transfer enhancement and pressure loss caused by different shapes and configuration of pin fin arrays and the optimization analysis shows that cube - shaped pin - fin arrays can be viable alternatives for pedestal cooling in a blade trailing edge

    本文提出了一個強化換熱有效性系數來綜合考慮擾流柱換熱和壓力損失的效果，並用它對各種擾流柱進行了優化分析，優化結果表明方形擾流柱排在渦輪葉片尾緣區冷卻結構設計中是優先考慮的一種結構型式。
  18. Measurements were made of system pressure, mass flow rate of steam, air, and cooling water, temperatures of condensing flow and cooling flow, and the water level of boiler. the major phenomena observed in the present experiment are similar to those by other investigators. the mass flow rate of steam, the system pressure and air content are the most important factors affecting steam condensation

    實驗結果表明，維持二次側冷卻水流量不變，無論對于純凈蒸汽還是含有空氣的蒸汽冷凝，隨著蒸汽發生器加熱功率的增大（即蒸汽流量增大） ，有效冷凝段長度將加長；當蒸汽中含有少量空氣，有效冷凝段長度也會明顯加長；提高系統壓力，有效冷凝段長度將縮短。
  19. The stainless steel and carbon steel can be excellently bonded under lower pressure by using silver intermediate sandwich materials and the oxide film on stainless steel can be destroyed effectively by argon gas shielding in the heating process

    結果表明，採用自製的銀基中間夾層材料可以使兩種母材在較低的壓力下實現良好的復合；加熱過程中採用氫氣保護能夠有效地去除不銹鋼表面緻密的氧化膜。
  20. The type of this article is " used for product ". it analyzes surface pollution of metal, hydro capacity and effect to wall piping quantitatively on the base of the rinsing of piping of hydraulic system of precise - rolling machine at the hot sequential rolling plant. by analysis, we confirm the fit flux and pressure when rinsing, design high - ability, high - efficiency, wide - applicability whole set equipment

    本論文的成果直接用於生產，以太鋼熱連軋精軋機液壓系統的鋼管清洗為背景，對金屬表面污染進行分析，對液壓鋼管沖洗時流體的性能和其對管道內壁的作用效果進行定量的分析，確定合適的沖洗流量和沖洗壓力，設計製造了能力大、效率高、效果好、適用廣的成套裝置。
分享友人
分享到 Line

分享到臉書